Contact Us

BQ7721609PWR

Brand: Texas Instruments
Texas Instruments BQ7721609PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7721609PWR — Power Management & Signal Chain | Superb Automation

BQ7721609PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7721609PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7721609PWR: voltage and temperature protection for 3 to 16 series cells

The BQ7721609PWR is a protector for packs from three to sixteen cells in series, and it does more than watch voltage. Alongside overvoltage and undervoltage it checks for an open wire on a cell input, and with an external thermistor on the board it adds overtemperature and undertemperature protection. The 09 option runs a four second overvoltage delay, keeps open wire detection enabled, uses 100 mV of undervoltage hysteresis and drives its output high to 6 V.

The part sits in a 24 pin TSSOP and is aimed at packs where the cell count is high enough that a single comparator per cell would need a lot of board area. Sixteen sense inputs, an open wire check, a thermistor input and a driver, all in a body 4.40 mm by 7.80 mm.

The accuracy figures are quoted in two places because they behave differently. At 25 C the overvoltage comparator holds plus or minus 10 mV. Across 0 to 60 C it holds plus or minus 20 mV. That doubling is the real number for a pack that works outdoors, and it is the one to use when the margin against the charger is calculated.

Key data for the BQ7721609PWR

FunctionOvervoltage, undervoltage, open wire, overtemperature and undertemperature protection
Cell count3 to 16 cells in series
Overvoltage range3.55 V to 5.10 V across the family options
Undervoltage range1.0 V to 3.5 V across the family options
AccuracyPlus or minus 10 mV at 25 C, plus or minus 20 mV from 0 to 60 C
Overvoltage delay4 seconds on the 09 option
Undervoltage hysteresis100 mV on the 09 option
Overtemperature75 C charge cutoff with an external NTC thermistor
Open wireDetection enabled on the 09 option
Output driveActive high, drives to 6 V
Supply currentAbout 1 microamp with all cells below the protection point
Cell input leakageLess than 100 nanoamps per input
Package24 pin TSSOP, 4.40 mm by 7.80 mm body
TemperatureMinus 40 to 110 C operating

The open wire check, and the fault it catches that voltage cannot

A cell input that has lost its connection reads as a voltage the pack does not have. In a sixteen cell stack the sense wire to one cell can break at a connector, and the comparator then sees the sum of the cells above it, or a floating node, depending on where the break sits. A protector that only compares voltage will either miss the fault or report an overvoltage that is not there.

The part pushes a small current into each input and looks at the resulting level, which is how an open wire is separated from a real cell reading. The cost of that check is a small continuous current on each sense line and a requirement that the series resistors in front of the inputs be sized so the check still works. A 1 kilo ohm resistor that protects the input from a short also swamps a check that expects a much higher impedance.

This is the fault that shows up in the field as a pack that goes to protection at random, with no history of overcharge and no hot cell. It is worth switching on whenever the pack has a connector between the cells and the board, which is most packs above ten cells.

Temperature protection with an external thermistor

The thermistor input gives the part a second reason to open the charge path. On the 09 option the charge cutoff is 75 C, which covers a pack that is being fast charged in a hot enclosure. The threshold is set by the option, not by a resistor divider, so the accuracy of the protection depends on the thermistor curve matching what the part expects, not on a trim in production.

Thermistor placement decides whether the protection is useful. A part that measures the board temperature near the connector will react to the connector, not to the cells. A part that measures one cell in a pack of sixteen will react late, because the hot cell is usually the one nearest the load path. The usual compromise is one thermistor per four cells, with the thresholds set against the worst case cell rather than the average.

Below the cutoff the part does nothing, and that is the intended behaviour. It does not fold back the charge current, it does not report the temperature to a host, and it has no way to log how close the pack came to the limit. Those jobs belong to the monitor, if the pack has one.

Where it fits in a build

Sixteen cells in series is the shape of an e bike pack, a light electric vehicle pack, a cordless tool pack built from two strings, or a small stationary storage module. In all of them the protector is the layer that must work when the monitor has failed or is still booting.

These builds usually run for several years on the same bill of material, and the part is ordered in reels of 2000 on the 24 pin body. For a programme that is being quoted now and built in two years, the safety stock planning page sets out how a buffer is sized against a build plan and how it is reviewed when the plan moves.

The sourcing side of this part is covered on the kitting service. For a pack that carries the protector, the FETs, the thermistor and the fuse on one release, that page covers how the line is kitted.

Questions we get on this code

What is the difference between the 09 and the 11 option? Both run a four second overvoltage delay and both drive high to 6 V. The 09 option keeps open wire detection on with 100 mV of undervoltage hysteresis, and the 11 option sets 200 mV of hysteresis and switches open wire detection off.

Can the part work without a thermistor? Yes, the temperature function is only active when a thermistor is connected. Leave the input at a level the part reads as in range, and confirm from the data sheet what that level is for the option in use.

Does the output drive a contactor coil? No, it is a gate level drive to 6 V. A contactor needs a driver and a coil suppression path, and the coil supply has to be separate from the pack sense path.

How does the four second delay interact with a short circuit? It does not, the delay only applies to the overvoltage comparator. Current events are handled by a separate path, usually a fuse, a contactor and the monitor, and the protector is not sized for them.