Contact Us

BQ771807DPJR

Brand: Texas Instruments
Texas Instruments BQ771807DPJR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ771807DPJR — Power Management & Signal Chain | Superb Automation

BQ771807DPJR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ771807DPJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ771807DPJR: fixed threshold overvoltage protection for a 2 to 5 series pack

The BQ771807DPJR is an overvoltage monitor and protector for lithium ion packs built from two to five cells in series. Each cell is monitored on its own sense input, and the part does not measure the pack, it measures every cell and reacts to the first one that crosses the limit. The 807 option is listed at 4.450 V with 50 mV of hysteresis, a one second internal delay and an open drain output that pulls low on a fault.

Everything about the part is fixed. There is no register map, no bus, no way for a host to read a cell voltage or change a threshold. That is the point of the family. A protection layer that cannot be reconfigured also cannot be left in a wrong state by a bus error or a brown out, and it keeps working while the rest of the board is still booting.

The two numbers that decide whether it fits are the threshold tolerance and the quiescent current. The overvoltage comparator is specified at plus or minus 10 mV, so a 4.450 V option trips somewhere between 4.440 V and 4.460 V on a fresh part at room temperature. The part draws about 1 microamp from the cells when all cell voltages sit below the protection point, and each sense input leaks less than 100 nanoamps, which is what allows it to sit permanently across a pack that is stored for a year.

Key data for the BQ771807DPJR

FunctionOvervoltage monitor and protector, one comparator per cell
Cell count2, 3, 4 or 5 cells in series
Overvoltage threshold4.450 V on the 807 option, 3.850 V to 4.650 V across the family
Threshold accuracyPlus or minus 10 mV
Hysteresis50 mV on the 807 option
DelayInternal, 1 second on the 807 option, no external capacitor
OutputOpen drain, active low
Supply currentAbout 1 microamp with all cells below the protection point
Cell input leakageLess than 100 nanoamps per input
Test modeCustomer test mode shortens the delay for production line checks
Package8 pin QFN, 3.00 mm by 4.00 mm, and 8 pin MSOP on other options
TemperatureMinus 40 to 110 C operating

What a fixed threshold means when the cells are not matched

The part trips on the highest cell, not on the pack. In a five cell pack with one cell that has aged to a higher impedance, the charger pushes that cell up first, and the protection point will be reached while the other four are still below 4.2 V. The pack then stops charging with usable capacity left in it, and the user sees a pack that charges slowly and runs short.

The hysteresis number is what governs recovery. With 50 mV, the output releases once the offending cell falls back to about 4.400 V. On a charger that holds a constant 4.45 V per cell, the pack can sit on the edge and cycle the output. A pack that shows this behaviour usually needs either a lower float voltage or a balancing path that keeps the cells together, because the protector is reporting a real condition rather than a fault of its own.

Threshold tolerance also matters at the top of the charge window. A 4.450 V option with plus or minus 10 mV, measured at the cell, leaves very little room against a charger set to 4.40 V per cell. That 50 mV gap is deliberate, but it assumes the sense wiring is short and Kelvin connected at the cell tab. A long trace that carries charge current in the sense path will add an error larger than the tolerance of the part.

The internal delay timer, and what it changes on the line

Because the delay is generated inside the part, there is no external timing capacitor to select, place or validate. On a board that carries four of these devices for different pack builds, that removes a part number from the bill of material and a tolerance from the test plan. The one second delay is long enough to ignore the spike that a charger makes when it is plugged in, and short enough to protect the cells from a real overcharge.

The customer test mode exists for the production line. In normal operation a technician who wants to see the output change has to wait a full second, and on a fixture that checks a few hundred boards a day that wait adds up. Test mode shortens the delay so the output responds quickly enough to be captured by the fixture, then the board is returned to normal operation. What the fixture must not do is leave a board in test mode, because a protector whose delay is short will trip on events that the pack should ride through.

One limit of the arrangement: the part has no way to report that it has tripped and recovered. The host sees a pack that stopped charging, and nothing else. A product that needs a fault log has to watch the output pin from a microcontroller or add a protector with a status path.

Where it fits in a build

This is the second protection layer in a small pack: power tools, garden equipment, vacuum cleaners, small medical carts, backup packs. It sits next to a primary protector that handles current, and it takes over the overvoltage job with a tighter threshold. It also suits packs that are potted or sealed, because there is nothing to adjust after the build.

For a programme that runs for years on the same pack, the part is a repeat item and the supply question becomes one of date code and packaging rather than technology. The component lead time solutions page sets out how we hold buffer, how we check reel age and what we confirm before a delivery date is given.

The sourcing side of this part is covered on the date code management. For a protector that may sit in stores before it is fitted, that page covers how reel age is tracked and what we will not ship into a new build.

Questions we get on this code

Can two of these be stacked for a ten cell pack? Not directly. The output of one part cannot drive the sense input of another, and the family is specified for 2 to 5 cells. A ten cell pack needs a protector that is rated for the series count, and the pin count and the isolation between the high side and the low side change with it.

Does the open drain output need a pull up? Yes, and the resistor has to be returned to a rail the host can read, not to the pack. In a pack that sits at 18 V, pulling up to the pack would put 18 V on a host pin. The usual arrangement is a 100 kilo ohm pull up to the 3.3 V rail of the controller, with the output pin rated for the pack voltage.

What happens if one sense input is left open? The comparator sees whatever the leakage and the routing allow, and the behaviour is not defined by the data sheet. On a five cell option used on a four cell pack, the spare input has to be tied to a defined level, otherwise the output can sit in a state nobody expects.

Is the part sensitive to the order the cells are connected? Yes. The sense inputs have to come up in a defined order relative to the supply pin, and a pack that is connected in the field can violate that order. A series resistor in each sense line, sized against the input leakage and the ADC of any monitor sharing the node, is the usual protection.