BQ51013CRHLR
Product Specifications
BQ51013CRHLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ51013CRHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ51013C: the receiver side of a 5 W Qi link
The BQ51013C is a wireless power receiver for the Qi standard at version 1.3. It sits on the secondary side, takes the AC from the receiver coil, rectifies it, regulates the output to 5 V, and runs the communication that tells the transmitter how much power to send. Between the coil and the output it is the only IC needed, which is why a wireless charging function can be added to an existing product without a rebuild of the power path.
The rectifier is synchronous, so the forward drop that a diode bridge would produce is mostly gone. The vendor quotes 93 per cent peak AC to DC efficiency, and that figure is the difference between a receiver that runs cool in a sealed enclosure and one that needs a thermal path. Peak efficiency is a best case number taken at a particular coil and load, and the number that matters in a product is the efficiency at the load the product actually draws.
The package is a 20 pin VQFN at 4.50 mm by 3.50 mm with an exposed pad that has to be soldered to ground for both electrical and thermal reasons. The output is fixed at 5 V, the maximum output power is 5 W, and the input is rated to 20 V so a misaligned coil or a foreign object does not take the part out on the first event.
Key data for the BQ51013C
| Function | Qi v1.3 wireless power receiver with integrated rectifier and regulator |
| Output | 5 V regulated, up to 5 W |
| Efficiency | 93 per cent peak AC to DC |
| Rectifier | Full synchronous rectifier, no external diodes |
| Input rating | 20 V maximum at the rectifier output |
| Overvoltage clamp | Dissipative clamp at 15 V |
| Foreign object detection | Enabled, with an accurate current sense for the power loss calculation |
| Communication | Adaptive communication limit for a stable link across coil misalignment |
| Control pin | Multifunction NTC and control input for temperature, charge complete and fault signalling |
| Thermal | Thermal shutdown |
| Package | VQFN, 20 pins, 4.50 mm by 3.50 mm, exposed pad to ground |
| Ordering | BQ51013CRHLR, 3000 pieces on a large tape and reel, moisture level 2 with a one year floor life |
The 20 V input rating, and the event it is there for
A wireless receiver sees a voltage that depends on how well the coil is coupled and how hard the transmitter is driving. Move the phone half off the pad and the coupling falls, so the transmitter turns up its drive to hold the same received power, and the rectified voltage rises. That is the normal case, not a fault, and it is why the rectifier has to survive more than the 5 V it regulates to.
The 15 V clamp is the second layer. It burns the excess as heat rather than letting the rail run away, and it is sized for the short interval before the communication loop tells the transmitter to back off. The 20 V rating is the ceiling above that clamp, and a part that is asked to sit at that ceiling for long will be limited by its thermal path rather than by its silicon.
Foreign object detection is the third layer, and it is a safety function rather than a protection one. A coin or a key on the pad absorbs power and heats up, and nothing in the electrical path will notice because the power is simply not arriving at the receiver. The current sense in this part feeds the loss calculation that lets the receiver compare what was sent with what arrived, and the difference is what triggers the fault.
Coil, capacitors and the thermal path
The receiver coil is not part of the IC, and it decides as much of the performance as the IC does. Its inductance and its series resistance set the resonant tank with the series and parallel capacitors, and the values in the vendor reference build only hold for the coil used in that build. A different coil means the tank has to be recalculated, and a tank that is off resonance loses efficiency in a way no amount of tuning in the part will recover.
The output capacitor is the other item that shows up in field returns. The regulator loop expects a certain range of output capacitance, and a part with a much larger capacitor starts slowly and can trip the communication before the rail is up. Start with the value in the reference build and change it only with a reason.
Thermally, the exposed pad is the only path out of a 3.5 mm by 4.5 mm body. On a 5 W receiver at 93 per cent peak, the loss is a few hundred milliwatts, which is easy to dissipate through a pad tied to a ground plane and impossible to dissipate through a pad tied to a thin trace.
Where it fits in a build
Sealed products where a connector is a liability: ultrasound probes, headsets and earbud cases, handheld instruments, industrial sensors, medical devices that have to be wiped down. The 5 W ceiling suits a product that charges a small battery over hours rather than a phone that expects a fast charge.
Wireless charging products also bring a compliance question with them, because the Qi mark is a certification and not a description. On a programme that needs the certification evidence to travel with the build, the supplier quality audit page covers the records we ask for and keep.
The sourcing side of this part is covered on the one stop BOM sourcing. For a product that adds a coil, a receiver and a shield on one BOM, that page covers how the parts are grouped and released together.
Questions we get on this code
Does it work with any Qi transmitter? It follows the Qi v1.3 protocol, so it works with transmitters that implement the same version. An older transmitter that predates the protocol revision may still charge, but the communication margin and the foreign object behaviour are not guaranteed.
Why is the output fixed at 5 V? That is the Qi baseline. A product that needs a different rail has to add its own converter after the receiver, and the efficiency of that converter has to be counted against the link efficiency before the thermal budget is signed off.
What does the multifunction pin do? It takes a thermistor to watch the battery or the coil, it signals charge complete back to the transmitter, and it can be used to report a fault to the host. One pin, three jobs, and the resistors around it decide which job it does.
Is the 93 per cent figure what the product will measure? Only at the peak point of the curve with the reference coil. A real product at its own load, with its own coil and its own spacing, typically measures below the peak, and the board has to be checked at the load the product actually draws.