Contact Us

BQ41Z50RSNR

Brand: Texas Instruments
Texas Instruments BQ41Z50RSNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ41Z50RSNR — Power Management & Signal Chain | Superb Automation

BQ41Z50RSNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ41Z50RSNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ41Z50RSNR: a pack manager for two to four cells in one body

The BQ41Z50RSNR is a complete pack manager for two, three or four series cells. It carries the gauge, the protection path and the authentication in one 32 pin package, which is why a pack built around it needs very little else on the board besides the FETs, the sense resistor and the cell connections. The part runs from a 32 bit processor inside the package and reports to the host over an SMBus interface.

The supply pins tolerate up to 40 V, so a four series pack that sits at 16.8 V has plenty of headroom for transients. Protection is handled by high side N channel FET drive with configurable strength, and the drive is generated by an internal charge pump, which keeps the FETs on the high side of the pack where the ground reference stays clean.

Two independent 16 bit converters run the measurements: one for current and one for voltage, and they can sample at the same time. That simultaneity is what lets the part pair a current reading with a voltage reading taken in the same instant, which is the only way to get a clean impedance number while the load is moving.

Key data for the BQ41Z50RSNR

FunctionPack manager with gauging, protection and authentication
Cell count2, 3 or 4 series cells, Li-ion, LiPo or LiFePO4
Supply tolerancePower supply pins rated to 40 V
ConverterTwo independent 16 bit converters, simultaneous current and voltage sampling
Temperature inputsUp to four external thermistors plus an internal sensor
ProtectionOvervoltage, undervoltage, overcurrent in charge and discharge, short circuit, overtemperature, charge timeout
FET driveHigh side N channel charge and discharge drive with configurable strength
InterfaceSMBus v3.2 compatible, host reads gauging and status registers
Active current475 microamps typical in the higher performance gauging setting, 315 microamps in the other
Sleep and shutdown165 or 155 microamps in sleep, 0.8 microamps in shutdown
PackageWQFN, 32 leads, exposed thermal pad
OrderingBQ41Z50RSNR, 3000 pieces on a large tape and reel, moisture level 2 with a one year floor life

What dynamic impedance tracking changes in a tool pack

A power tool pack is asked for a 20 A pulse from a pack that has been sitting at 60 per cent charge, and the voltage the tool sees is not the rested voltage minus a fixed drop. It is the rested voltage minus a drop that depends on the state of charge, the temperature and the age of the cell. Dynamic tracking models that drop as it happens, so the gauge can tell the host how much power is actually available right now rather than how much charge was in the pack this morning.

That number is what a system uses to decide whether to allow a boost mode, to limit a motor to a lower speed, or to refuse a start. A gauge that reports remaining capacity alone leaves that decision to a fixed threshold, and a fixed threshold on an ageing pack trips early and gives the user a tool that feels weak before the pack is empty.

The measurement that supports this is the simultaneous one. If current and voltage are sampled a few hundred microseconds apart, the pair describes two different operating points, and the impedance calculated from them is wrong. The two converter arrangement exists to remove that error.

The protection path, and the parts it needs around it

The charge and discharge FETs sit in the pack positive path, driven by the internal charge pump. High side drive keeps the pack negative as a solid ground reference, which matters on a tool that shares its negative with a charger and a motor controller. The trade is that the gate drive has to be generated above the pack voltage, and the pump inside the part does that.

The strength setting is there for a reason. A large FET has a large gate charge, and driving it too softly turns the switch through its linear region slowly, which heats it. Driving a small FET too hard rings on the gate and radiates. The setting has to be matched to the FET actually fitted, and it is one of the few items on this part that a change of FET vendor will force you to revisit.

The secondary chemical fuse drive is separate from the FET path. It is there for the case where the FETs have failed closed or the current is beyond what they can interrupt, and it fires a one time fuse. That fuse has to be chosen with the pack, because the drive pulse is not sized for every fuse on the market.

Where it fits in a build

Two to four series packs with a real protection requirement: cordless power tools, garden equipment, vacuum cleaners, light electric vehicles, non military drones and industrial packs. It is also a natural fit where the pack has to authenticate itself to the tool, because the SHA based challenge and response sits inside the same package as the gauge.

Packs in this class are built in volume and re built on a several year cycle, so the reel size and the moisture level matter as much as the silicon. BQ41Z50RSNR ships 3000 to a reel at moisture level 2 with a one year floor life, and the incoming inspection plan page covers what we check at the receiving dock on a part in that body.

The sourcing side of this part is covered on the kitting service. For a pack that carries the monitor, the FETs and the fuse on one release, that page covers how the line is kitted.

Questions we get on this code

Does the pack need a separate protector IC? No, the protection comparators and the FET drive are inside this part, and the configuration sets the thresholds. A separate protector only makes sense when the pack has to meet a standard that requires an independent second device.

Can the same part build a 2S and a 4S pack? Yes, the cell count is a configuration item and the sense inputs cover the range. The cell count, the thresholds and the gauging model all change with it, so the two packs do not share a configuration file.

What current can it measure? The converter reads across an external sense resistor, and the range is set by that resistor. The part itself does not limit the current, the FETs and the fuse do.

Is the authentication mandatory? No, the pack can run without it. On a programme where third party packs are a commercial risk, the challenge and response is the cheapest way to make a non genuine pack fail to start.