BQ27427YZFR
Product Specifications
BQ27427YZFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ27427YZFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ27427YZFR: the same 9 ball gauge, drawing half the current
The BQ27427YZFR is the newer member of the system side gauge family. It carries the same integrated 7 milliohm sense resistor, the same 9 ball chip scale body and the same 400 kHz I2C interface as the earlier part, and it brings the normal mode current down to 50 microamps with a 9 microamp sleep figure. For a wearable or a handset that spends its life in a low power state, that difference is the reason to choose this row over the older one.
The second change is configuration. Three chemistry profiles are pre programmed, so a line that builds packs from more than one cell supplier does not have to reload a chemistry identifier for each variant. The gauge picks from the stored profiles, which keeps one part number across projects with different cells and takes a step out of the programming flow at the pack house.
The body is the familiar 9 ball DSBGA at 1.58 mm with 0.5 mm pitch, and the part runs directly from the battery through an internal regulator. The sense resistor is inside the die, so the current path is the two pack connections and nothing else.
Key data for the BQ27427YZFR
| Function | System side fuel gauge for one Li-ion cell, Impedance Track algorithm |
| Sense element | 7 milliohm resistor integrated on the die |
| Chemistry profiles | Three profiles stored in the part, no reload per cell variant |
| Normal current | 50 microamps typical |
| Sleep current | 9 microamps typical |
| Temperature input | Internal sensor, host reported value, or an external 10 kOhm NTC |
| Default thermistor | Coefficients assume a Semitec 103AT at 10 kOhm at 25 C |
| Interface | I2C at 400 kHz, configurable state of charge interrupt or battery low output |
| Reports | Remaining capacity, state of charge with smoothing filter, voltage, state of health |
| Package | DSBGA, 9 balls, 1.58 mm, 0.5 mm pitch |
| Temperature | Minus 40 to 85 C operating |
| Ordering | 3000 pieces on a large tape and reel, moisture level 1 at 260 C |
Reading the 50 microamp figure honestly
The headline number is the normal mode current, and it applies when the load is above the sleep threshold. Below that threshold the part drops into sleep at 9 microamps, and the transition is automatic. A battery life sum that uses 50 microamps for every hour overstates the drain on a product that spends most of its time idle, and a sum that uses 9 microamps everywhere understates it during active periods.
The comparison that matters is against the older 93 microamp member. On a 300 mAh wearable cell, the difference between 93 and 50 microamps is about 0.34 mAh per day, which is roughly 0.1 per cent of the pack per day and around 4 per cent a month. That is not a reason to change a running product, and it is a reason to pick the newer row for a new one.
The sleep figure is where the gap widens. 21 microamps against 9 microamps is more than half the idle drain removed, and on a product that sits in a drawer between uses the idle drain is the number the customer notices.
What the three stored profiles change in production
Each profile is a set of open circuit voltage against state of charge points and a resistance model for one cell chemistry. With three stored, the gauge can be configured at the pack house by selecting a profile rather than by loading a table through the vendor tool. For a line that builds the same board with two cell suppliers, that removes a step that is easy to get wrong and hard to catch, because the wrong profile does not fail a test, it just reports a state of charge that drifts.
Storing three profiles is not a licence to skip the check. The selected profile has to match the cell in the pack, and the only reliable record is the build paperwork. A pack that reports 8 per cent low after a cell change is usually a profile mismatch rather than a gauge fault.
The external thermistor route is worth using when the pack is not adjacent to the board. The default coefficients assume a 10 kOhm negative temperature coefficient part of the 103AT type, so a different thermistor curve needs its own coefficients. A generic 10 kOhm part with a different beta will read a few degrees off at the ends of the range, which is enough to shift the resistance model.
Where it fits in a build
This is the row to pick for a new single cell product with a tight idle budget: wearables, handheld instruments, battery powered sensors and portable medical devices. It is not the row for a two cell pack, and it is not the row for a pack where the gauge must live on the cell flex inside a sealed enclosure, because the integrated sense resistor needs the current to pass the board.
For a wearable BOM that carries this gauge plus a charger, a protection device and a handful of passives, the one stop BOM sourcing page covers how we kit the whole line rather than the gauge alone.
The sourcing side of this part is covered on the date code management. For a reel that will be split across two build dates, that page covers how we track reel age and what we will not ship into a new run.
Questions we get on this code
Is the BQ27427 a drop in replacement for the earlier gauge? Electrically the body, the ballout and the supply arrangement are the same family, and the register map follows the same command structure. Treat it as a new part for qualification, because the current figures, the stored profiles and the default thermistor coefficients differ, and a board that was signed off on the older part has not been tested on this one.
Does the part need a battery inserted to answer on the bus? It answers as soon as it has supply. The gauging values need a cell to mean anything, but the identification and the configuration registers read back with no pack fitted, which is what a factory fixture needs.
What if the pack thermistor is left unconnected? The gauge falls back to its internal sensor, which reads the die and therefore the board. On a board that runs warm the reported temperature is higher than the cell, and the model then predicts more internal resistance than the cell has.
How do we know which profile is loaded? Read it back over I2C at the end of the programming step and record it against the serial number. The part does not print the profile on the top of the die, so the record is the only evidence after the pack is closed.