BQ27220YZFR
Product Specifications
BQ27220YZFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ27220YZFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ27220: a single cell CEDV gauge with a 10 milliohm sense resistor
The BQ27220YZFR is a single cell fuel gauge that runs the compensated end of discharge voltage algorithm in the part and reports remaining capacity in mAh, state of charge in per cent, runtime to empty in minutes, voltage in millivolts, temperature in degrees and state of health in per cent. It sits in the pack or on the system board, powers itself from the cell through an internal regulator, and talks over a 400 kHz I2C bus.
Two numbers define the part's place in a product. The first is the sense resistor: 10 milliohms is low enough that the gauge does not waste measurable energy in the measurement path. The second is the current draw: 50 microamps in normal mode and 9 microamps in sleep. On a pack that spends most of its life in standby, that difference decides how much of the shelf life is left for the product.
The CEDV algorithm is a model rather than a counter. It uses voltage, current and temperature together, and it corrects for aging, self discharge and rate. That is what allows a gauge to keep reporting a sensible state of charge after the pack has lost a fifth of its capacity, which a pure coulomb counter cannot do.
Key data for the BQ27220YZFR
| Function | Single cell CEDV fuel gauge, pack or system board |
| Sense resistor | 10 milliohms external |
| Current draw | 50 microamps normal, 9 microamps sleep |
| Reports | Remaining capacity, state of charge, runtime to empty, voltage, temperature, state of health |
| Interface | I2C at 400 kHz |
| Configuration | Preloaded ROM parameters, or custom parameters through GAUGEPARCAL |
| Storage | Onboard one time programmable memory for custom parameters |
| Temperature sensing | External thermistor |
| Interrupts | Configurable, to free the host from polling |
| Package | DSBGA, 9 balls, YZF body, marking BQ27220 |
| Temperature | Minus 40 to 85 C operating |
The configuration route is worth planning before the first build. Parameters loaded from ROM suit a common chemistry, and a pack with a different cell needs its own model. That work happens at the pack house with the vendor tool, and the result is written once.
Body and ordering data
BQ27220YZFR is active and in production: DSBGA YZF with 9 balls, 3000 pieces on a large tape and reel, SNAGCU finish, moisture level 1 at 260 C with no floor life limit, minus 40 to 85 C, marking BQ27220. The same string is offered at 250 pieces on a small reel, which is the row to take for a pilot build.
The one time programmable memory is a production decision, not a cosmetic detail. Parameters written to OTP cannot be changed afterwards, so a pack that is calibrated at the bench and then found to be wrong is a scrapped pack. The parts ship with ROM defaults that suit a common chemistry, and the OTP route is for a product that has the model settled before volume.
The sense resistor is the accuracy floor
At 10 milliohms, a 1 A discharge develops 10 mV across the sense element. The gauge resolves a fraction of that, and the resolution in current sets the resolution in capacity. A larger resistor improves the signal and wastes more power. A smaller one wastes less and needs a better amplifier. The 10 milliohm figure is the compromise the part was specified around, and substituting 5 milliohms without changing the configuration halves the current resolution and doubles the noise floor.
The kelvin connection matters here as much as on a charger. A sense trace taken from the power path instead of the resistor pads adds the copper resistance to the measurement, and copper moves about 0.4 per cent per degree, so the error changes with temperature over the charge cycle.
Where it fits in a build
Tablets, handheld instruments, medical monitors and gaming devices with a single cell and a host that can read I2C. The 9 microamp sleep current makes it usable in a product that sits idle for weeks. The medical device components page covers the traceability points for the monitor market.
A product that needs a 2 cell gauge, or one that has to survive above 85 C, needs a different family. A product with no host at all needs a gauge with a display driver rather than an I2C part.
The sourcing side of this part is covered on the date code management. For a gauge that is programmed at the pack house, that page covers how we handle date codes and the one time programmable step in the flow.
Questions we get on this code
Does it need the host to run the algorithm? No. The CEDV model runs inside the part; the host reads results.
Can the parameters be changed after assembly? Only in the RAM shadow before the OTP is written. After that the model is fixed for the life of the part.
What is state of health? A percentage that compares the present capacity with the original, which is the number a service decision is based on.
Why 400 kHz I2C? Because the gauge is polled often and a slow bus costs host time. The part also supports interrupts so the host does not have to poll at all.