Contact Us

BQ25892RTWR

Brand: Texas Instruments
Texas Instruments BQ25892RTWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25892RTWR — Power Management & Signal Chain | Superb Automation

BQ25892RTWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25892RTWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25892: a 5 A charger for high voltage adapters

The BQ25892RTWR is an I2C controlled single cell charger that takes up to 5 A of charge current from a 1.5 MHz buck stage fed by an input between 3.9 V and 14 V. The high input range is the point: a 9 V or 12 V adapter can push 5 A into the pack through a standard cable, where a 5 V adapter would need a cable and a connector that cannot carry it.

Efficiency is quoted at 93 per cent at 2 A and 91 per cent at 3 A. The 5 A figure is the peak of the family, and it depends on the adapter being able to supply it, the inductor being sized for it, and the thermal path carrying the loss.

The boost direction runs from the pack to a 4.5 V to 5.5 V output at up to 2.4 A, with selectable 500 kHz and 1.5 MHz operation. A phone that charges at 5 A and then sources 2.4 A to an accessory is using the same four FETs in both directions, which is why the part has a single input rather than a separate boost converter.

Key data for the BQ25892RTWR

FunctionI2C controlled single cell 5 A buck charger with OTG boost
Charge currentUp to 5 A
Input range3.9 V to 14 V operating
Switching frequency1.5 MHz buck, 500 kHz or 1.5 MHz boost
Efficiency93 per cent at 2 A, 91 per cent at 3 A
Input current limit100 mA to 3.25 A in 50 mA steps
Boost output4.5 V to 5.5 V adjustable, up to 2.4 A
DetectionAuto detect USB SDP, CDP, DCP and non standard adapters
ProtectionHiccup mode overcurrent, thermal regulation, battery temperature sensing in both directions
PackageWQFN, 24 pins, RTW body, 4 mm by 4 mm
TemperatureMinus 40 to 85 C operating

The charge current also has to be matched to the inductor and the output capacitance. At 5 A the ripple current in a 1 microhenry inductor is large, and the output capacitor sees an RMS current that heats it. A board that runs 3 A comfortably will not run 5 A on the same passives, which is why the current setting and the passive choice move together.

Body and ordering data

BQ25890 and BQ25892 share the document and the body. They differ in the OTG behaviour and in the register map around the boost mode. Both are in the RTW body with 24 pins at 4 mm by 4 mm, 3000 pieces on a large tape and reel, NIPDAU finish, moisture level 2 with a one year floor life, minus 40 to 85 C, marking BQ25892. The G4 rows carry the same body and quantities.

Both strings are active. The addendum prints the BQ25890 rows first, and the BQ25892 row sits further down the same block with the same package and the same reel. A quote that names the family without the string can deliver either die.

The input limit is what protects the cable

A 5 A charge current from a 9 V adapter is about 45 W at the input, and a USB cable with 0.3 ohm of resistance drops 1.5 V at 5 A. The adapter sees 10.5 V and the connector dissipates 7.5 W, which is enough to soften a moulded plug. The input current limit is set below the cable rating, not at the adapter rating, and the auto detect only tells the charger what class the source claims to be.

The maximum power tracking function follows the input voltage down as the current rises and folds the current back before the adapter collapses. On a long cable that behaviour is what keeps the product from cycling between charge and no charge.

Where it fits in a build

Phones, tablets, portable internet devices and any single cell product that charges from a 9 V or 12 V adapter. The component lead time solutions page sets out what we check on the input detection and boost behaviour before offering a substitute.

A product limited to a 5 V adapter does not need this part, and the 14 V input rating is wasted. A product with a 2 cell pack needs a controller, not an integrated charger.

The sourcing side of this part is covered on the power management cross reference. For a phone platform comparing the 5 A members of this family, that page lists the input limits and boost behaviour we compare first.

Questions we get on this code

Is 5 A available on a standard USB cable? Not safely. The 5 A figure assumes a short, low resistance path and an adapter that can hold 9 V at that current. Most boards run 2 A to 3 A on a normal cable.

Does the boost work while charging? No. The two directions are separate modes.

What is the difference from the BQ25890? The OTG control and the register definitions around it. The charge engine is the same.

Why does the input range stop at 14 V? Because a higher input would need a different process and a different FET set, and the 12 V adapter class is where this market sits.