BQ25798RQMR
Product Specifications
BQ25798RQMR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25798RQMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25798RQMR: I2C Buck-Boost Charger for One to Four Cells With MPPT
BQ25798RQMR is an I2C controlled buck-boost battery charger for one to four lithium cells in a 29-pin VQFN body of 29 pins. It takes 3.6 V to 24 V in, charges at up to 5 A, and holds the system rail above the battery while the pack is flat, with a maximum power point tracker for a solar input and a second input selector.
Order code and package
| Ordering string | BQ25798RQMR, VQFN-29 (RQM), 4 mm by 4 mm |
| Second package | DSBGA-56, 2.9 mm by 3.3 mm, for the space constrained build |
| Input | 3.6 V to 24 V recommended, 30 V absolute maximum |
| Battery | 1 to 4 cells, up to 18.8 V |
| Charge current | up to 5 A, 3.3 A shown in the fast charge range |
| Path | NVDC power path with battery supplement and USB OTG output |
Electrical parameters that decide the application
| Switching frequency | 750 kHz and 1.5 MHz settings |
| Battery quiescent, enabled | 17 uA typ, 24 uA max, no VBUS |
| Battery quiescent, ship mode | 11 uA typ, 16 uA max |
| Shutdown battery current | 0.5 uA typ, 0.7 uA max |
| Input quiescent, switching | 3 mA typ, 5 mA with the coulomb counter on |
| Input shutdown, HIZ mode | 386 uA, 590 uA with the adapter driver enabled |
| Discharge current | 5 A continuous, 5 A peak for up to one second |
| MPPT | input voltage regulation against a scaled open circuit voltage |
| ADC | integrated, for input, battery and system readings |
| Interface | I2C, with a default register set that starts charging without a host |
Points to check before this part goes on a BOM
Five amps into an 8.4 V pack is 42 W, and at 95 percent efficiency from a 5 V source that is 8.84 A of input current, which is above the 5 A a USB-C connector is rated for. The 5 A charge current is therefore reachable from a 12 V or 20 V adapter and not from a 5 V one, and the input current limit register is what keeps a 5 V source from being dragged down.
Ship mode at 16 uA maximum is 140 mAh over a year and shutdown at 0.7 uA is 6 mAh, so the state that matters for a product sitting in a warehouse is ship mode and its 11 uA typical, not the shutdown figure. Two cells of 3000 mAh lose about 2 percent of their charge a year to this part and rather more to their own self discharge.
The input is rated 24 V recommended and 30 V absolute, so a 24 V industrial rail at plus 10 percent sits above the recommended maximum and below the absolute one. That is a region where the part keeps working but the datasheet no longer promises the limits, and a 24 V rail needs a clamp rather than reliance on the 30 V number.
The maximum power point tracker works by scaling the measured open circuit voltage down to an operating point, so a panel with an 18 V open circuit is pulled towards roughly 15 V under load. The scaling factor is a register, which means a panel with an unusual fill factor can be tracked at the wrong point and the symptom looks like a weak panel rather than a setting.
Battery supplement mode lets the system draw more than the adapter can supply, with the pack making up the difference. That is what keeps a laptop running on a 45 W adapter while the processor boosts, but it also means the pack is being discharged while the charger reports charging, so a fuel gauge that assumes one direction will drift.
The integrated converter reads input voltage, battery voltage and system current, and the same front end does the coulomb counting, so the accuracy of a fuel gauge built on this part is its offset over the sense resistor. One millivolt of offset across a 10 mOhm sense resistor is 100 mA of standing error, which over ten hours is 1 Ah, a third of a small pack.
The I2C interface keeps the last register set if the host stops talking, so a charger configured by firmware carries on charging after the processor resets. That is what a device that must not stop charging wants, and it is also why a fault recovery that assumes a reset clears the limits does not work: the limits survive the reset and the fault repeats.
Where this order code fits
Portable instruments, solar powered nodes, medical carts and ruggedised tablets use this part where a single charger has to accept USB, an adapter and a panel into the same pack. A solar powered node that charges from a panel by day and runs from the pack at night uses the tracker and the ship mode together, and the same part covers a handheld that charges from USB-C and from a 12 V car adapter on the same input pin. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
How many cells does it support? One to four in series, up to 18.8 V, with the cell count set in a register rather than by a pin.
Can it charge from a solar panel? Yes. The tracker scales the open circuit voltage and regulates the input against it, and the scaling factor is programmable because panels differ.
What happens when the adapter is too small? The system rail is held and the battery makes up the difference, which is supplement mode. The pack discharges while the charger is still enabled.
Does it need a host processor to start? No. The default register set starts a charge cycle, and the host is only needed to change limits or read the converter results.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.