BQ25792RQMR
Product Specifications
BQ25792RQMR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ25792RQMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ25792RQMR: I2C controlled four switch buck boost charger for one to four cells in a 4 mm square QFN
BQ25792RQMR is a buck boost charger that takes 3.6 V to 24 V at the input, charges at up to 5 A and also drives a USB PD output from the battery in a VQFN-HR body of 29 pins. The part integrates the four switching FETs, the battery FET, both current sense paths and the loop compensation, so the external circuit is the inductor, a handful of capacitors and the sense resistors. It uses a narrow voltage DC power path, which holds the system rail just above the battery and lets the battery supplement the adapter when the load exceeds the input limit.
Order code and package
| BQ25792RQMR | VQFN-HR RQM, 29 pins, 4.0 mm by 4.0 mm, 3000 pieces on a large reel, Level-2-260C-1 YEAR |
| PQ25792RQMR | preview row on the same body at 3000 pieces, material declaration still open, not for volume orders |
| Temperature | minus 40 to plus 85 C operating free air temperature |
| Marking | BQ25792 on the body, which is how a mixed tray is sorted |
| Battery range | 1 to 4 cells in series, Li-ion and Li-polymer |
| Packing | the body is published on a large reel only, with no small reel row for prototypes |
Electrical parameters that decide the application
| Input voltage | 3.6 V to 24 V operating, 30 V absolute maximum at the VBUS pins |
| Charge current | up to 5 A with 10 mA of resolution in the register |
| Input current limit | IINDPM up to 3.3 A, with VINDPM tracking up to 22 V for a weak source |
| Switching frequency | 750 kHz or 1.5 MHz, chosen by register, which sets the inductor and the loss split |
| Efficiency | 96.5 per cent charging a 16 V battery at 3 A from a 20 V source |
| OTG output | 2.8 V to 22 V with 10 mV of resolution, current limited to 3.32 A with 40 mA steps |
| Battery only quiescent current | 21 uA, and 600 nA in charger shutdown, which is what protects a shelf life target |
| Monitoring | a 16 bit ADC for input, battery and system voltage, both currents and the junction temperature |
| System rail | SYS 2.5 V to 19 V, battery 0 to 18.8 V, with a programmable minimum system voltage |
Family variants and how they differ
| Dual input | VIN1 and VIN2 with an optional power mux, so a barrel jack and a USB-C port can share one charger |
| USB detection | BC1.2 for SDP, CDP and DCP sources plus HVDCP, so the input limit follows the source that is present |
| Autonomous mode | the charger can run from its default settings with no host, for a product that has no firmware path |
| Ship mode | the battery FET is opened so a finished product does not drain before it is unboxed |
| JEITA | the charge current and voltage follow the battery temperature profile through the TS pin |
| NVDC path | the system rail follows the battery plus a margin, and below the minimum system voltage the charger regulates the rail |
Points to check before this part goes on a BOM
NVDC is the reason a system rail is not a fixed rail. The charger holds the system node just above the battery, so a 3.3 V load on a 1S pack sees 3.0 V when the pack is nearly empty unless the minimum system voltage is set high enough. Set it from the lowest rail the load can accept, not from the nominal battery voltage.
The input current limit has to agree with the source. With a USB-C source the PD contract sets what the cable can carry, and the IINDPM register has to match it. A charger that asks for 3 A from a source that contracted for 1.5 A will pull the source down and the port will drop out, which reads as a charger fault.
Thirty volts is a transient rating, not an operating point. The input is rated for 24 V of operation and 30 V absolute, which is the margin for a barrel jack that is plugged in while the adapter is live. A product that regularly sees 26 V has the wrong front end, not the wrong charger.
Five amps in a four millimetre body is a thermal question. The only path out of the die is the exposed pad, so the pad needs a via field into a copper pour on the layer below. A footprint that follows the land pattern but leaves the pad on a thin trace will run hot long before the current limit is reached.
Ship mode is what protects the shelf. The battery FET is opened by command, and the part then draws 600 nA. A product that leaves the line in normal mode with a 21 uA draw and a year of shelf time is a warranty claim, and the fix is a line step rather than a component change.
OTG resolution is what makes PPS possible. The output moves in 10 mV steps up to 22 V, which is the granularity a PPS sink expects. An OTG path that only moves in 100 mV steps will be rejected by a phone that asks for a fine step.
Where the board goes wrong
The inductor is the part that decides the loss split between 750 kHz and 1.5 MHz. A part chosen for 1.5 MHz and then run at 750 kHz will saturate on a current step, and the symptom is a charger that restarts under load rather than one that runs hot.
The second common fault is a sense resistor placed between the input capacitor and the VBUS pin, which leaves the capacitor ripple out of the current measurement and makes the input limit read low. The vendor land pattern puts the resistor where the measurement includes the ripple, and it is worth following exactly.
What to ask a supplier for
For a build, ask for the reel size and the date code with the order code, because the preview row of this body carries the same marking and a different material status. The two are not interchangeable in a production record.
Ask also for the moisture level record. This body is published at Level 2 with a one year floor life, so a reel that has been open on a bench for longer than that needs a bake before reflow, and the label is the only record of when it was opened.
Where this order code fits
Video doorbells, smart home controllers, robotic mowers, vacuum robots, mobile point of sale terminals and patient monitors use this class of charger, because one part covers a barrel jack and a USB-C port and still drives the accessory from the battery. The 1 to 4 cell range lets one board serve several pack options. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can this part charge a 4S pack from a 5 V source? Yes, because the converter is a buck boost and the input range starts at 3.6 V. The input current limit then becomes the binding constraint, so a 5 V 3 A source charges a 4S pack at roughly the power the source can deliver divided by the battery voltage.
Does the host have to program anything to get a charge? Not with autonomous mode, which runs from the default settings. A product that needs a specific input limit, a specific charge profile or JEITA has to program it, and it has to do so at every power up because the registers are volatile.
What happens when the load exceeds the adapter? In the NVDC path the battery supplements the adapter, so the system rail holds and the input current stays inside the limit. That is the behaviour that keeps a peak load from resetting the product when a weak adapter is plugged in.
Is the 30 V input rating enough for a 24 V adapter? It is a 6 V margin over the operating maximum, which covers a plug in transient on a good adapter. It does not cover a 24 V rail with a load dump, and a product that sees one needs an external clamp in front of the charger.
What does the device report about the battery? The 16 bit ADC reads battery voltage, charge current, input current, system voltage and the die temperature, and the gauge that matters for state of charge is still a separate part. This charger reports what it is doing, not how much charge is left.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.