Contact Us

BQ25628RYKR

Brand: Texas Instruments
Texas Instruments BQ25628RYKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25628RYKR — Power Management & Signal Chain | Superb Automation

BQ25628RYKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25628RYKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25628: 2 A from an 18 V input, with narrow VDC power path

The BQ25628RYKR charges one cell at up to 2 A from a buck stage that runs at 1.5 MHz and accepts an input up to 18 V. The power path is the narrow VDC type: the system rail is held a little above the pack voltage and never below a configurable minimum system voltage, so a deeply discharged pack does not drag the processor down with it.

The part runs either autonomously or under I2C. Autonomously, the ILIM pin sets the input current limit and the temperature network sets the profile, with no bus traffic at all. Under I2C, current, voltage, termination and the JEITA thresholds are all registers. That flexibility is what allows one string to serve a product that boots with no software and then hands control to the host once the host is running.

The battery FET is not just a switch. It is controlled to support shutdown, ship mode and a full system reset, and the leakage figures in those states are the reason a sealed product can sit on a shelf. In battery only mode the part draws 1.5 microamps. In ship mode the pack leakage is 0.15 microamps.

Key data for the BQ25628RYKR

FunctionI2C or autonomous single cell buck charger with NVDC power path
Charge currentUp to 2 A
Input voltageUp to 18 V maximum input
Switching frequency1.5 MHz synchronous buck
EfficiencyAbove 90 per cent down to 25 mA output from a 5 V input
Voltage accuracyPlus or minus 0.4 per cent charge voltage regulation
Termination5 mA to 310 mA in 5 mA steps
Boost mode3.84 V to 5.2 V output for accessories
Leakage1.5 microamps battery only, 0.15 microamps in ship mode, 0.1 microamps in shutdown
Temperature profileFlexible JEITA over I2C, or the TS network in autonomous mode
PackageWQFN-HR, 18 pins, RYK body, marking BQ628
TemperatureMinus 40 to 85 C operating

Body and ordering data

Two dies share the document: BQ25628 and BQ25629. They differ in the default register settings and in the pin strapping, not in the converter. The orderable row here is BQ25628RYKR, WQFN-HR RYK with 18 pins, 3000 pieces on a large tape and reel, SN finish, moisture level 2 with a one year floor life at 260 C, minus 40 to 85 C, marking BQ628.

The RYK body is a leadless package with the pins on a 0.4 mm class pitch and the thermal pad taking most of the underside. It needs a stencil aperture that does not starve the pad. A pad with 50 per cent coverage will run the part hot at 2 A and the thermal loop will show it as a charge that never reaches its current.

Narrow VDC and why the minimum system voltage matters

In a traditional power path, the system rail follows the battery. When the pack is at 3.0 V, the processor runs at 3.0 V and may brown out. In narrow VDC, the system rail is held at or above a set minimum, and the battery FET operates in its linear region when the pack is below that floor, so the processor sees a stable rail while the pack catches up.

The cost is heat in the battery FET during that window. A product that starts from a flat pack every day runs that FET in linear mode for the first minutes of every charge, and the thermal path has to cover it. A product that is charged nightly from 60 per cent never sees the case.

Where it fits in a build

Portable speakers, TWS charging cases, hearing aid chargers, handheld instruments and medical portables. Any of those with a 5 V to 12 V input and a pack under 5000 mAh is in scope. The power management cross reference page lists what we compare when this string is short.

A product that needs more than 2 A of charge current moves to the 3 A and 5 A members of the family. A product with a 2 cell pack is outside this part and needs a controller with external FETs.

The sourcing side of this part is covered on the one stop BOM sourcing. For a product where the charger and the pack protection sit on one BOM, that page covers how we consolidate the two into one kit.

Questions we get on this code

Can it run with no I2C at all? Yes. The ILIM resistor sets the input limit and the part charges on its own from the first power up.

What does the 1.5 microamp battery only figure cover? The part with the adapter removed and the system in its lowest state. The system load is not part of that number.

Is the boost output regulated? Yes, between 3.84 V and 5.2 V, set by register. The 5 V setting is the one a USB accessory expects.

Why is the termination adjustable from 5 mA? Because a small pack charged at 2 A would otherwise terminate at a current that is a large fraction of its capacity, and the last part of the charge would be lost.