Contact Us

BQ25619RTWR

Brand: Texas Instruments
Texas Instruments BQ25619RTWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25619RTWR — Power Management & Signal Chain | Superb Automation

BQ25619RTWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25619RTWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25619RTWR: 1.5 A single cell charger with 20 mA termination and a 1 A boost for wearable charging cases

BQ25619RTWR is a single cell switch mode charger with narrow VDC power path and an integrated boost converter in a WQFN body of 24 pins. The part takes 4 V to 13.5 V in, charges at up to 1.5 A with 1.5 MHz switching, terminates at 20 mA with 10 mA accuracy, and runs the same inductor as a 4.6 V to 5.15 V boost at up to 1 A so a case can charge its own earbuds from its own cell.

Order code and package

Order codeBQ25619RTWR
PackageWQFN, 24 pins, 4.00 mm by 4.00 mm
Input voltage, operating4 V to 13.5 V
Input voltage, absolute maximum22 V with the converter not switching
Charge current1.5 A maximum
Switching frequency1.5 MHz
Termination current20 mA, plus or minus 10 mA
Ship mode current6 microamp
Boost output4.6 V to 5.15 V, up to 1 A
Safety certificationIEC 62368-1 CB

Electrical parameters that decide the application

Charge efficiency95.5 percent at 0.5 A, 94.5 percent at 1 A
Boost efficiency94 percent at 1 A
Charge voltage accuracyplus or minus 0.5 percent
Charge voltage step10 mV
Input current limit100 mA to 3.2 A in 100 mA steps
Input voltage limitup to 5.4 V, tracks the cell
JEITA profileprogrammable over I2C
Inductor size2.5 by 2.0 by 1.0 mm

Points to check before this part goes on a BOM

Twenty milliamps with 10 mA of accuracy is a 50 percent tolerance on the termination point. On a 40 mAh earbud cell that setting is 0.5 C, and the tolerance spans 0.25 C to 0.75 C, so the JEITA window and the safety timer decide when charging actually stops far more than the termination threshold does.

Six microamps in ship mode is 52.6 mAh over a year, which is 23 percent of a 225 mAh coin cell and a large share of a 60 mAh earbud cell. A product that ships with a partly charged cell and sits in a warehouse for a year needs the ship mode current in the shelf life calculation, not just the standby current of the rest of the board.

At 1.5 A into 4.2 V the charger delivers 6.3 W, and at 94.5 percent it draws 6.67 W, which is 1.33 A from a 5 V source. The 3.2 A input limit is there for a 13.5 V high voltage adapter, where the same setting would be 43 W, so the limit protects the source and says nothing about what the charger can pass.

The 22 V absolute maximum is specified with the converter not switching. A 13.5 V adapter plugged into a cable with a few microhenries of inductance rings well above its own voltage, and the input capacitor has to be at the connector for that rating to mean anything; a 20 V clamp in front of the part is cheap insurance for a hot plug event.

The input voltage limit tracks the cell voltage, up to 5.4 V, which is 1.2 V above a full 4.2 V cell. On a wireless receiver whose output sags under load this is the loop that keeps the system alive: the charger gives up current rather than letting the receiver collapse, and the system stays up at a lower charge rate instead of browning out.

Ten millivolts per step on the charge voltage means 4.20 V is reachable exactly, unlike parts with a 16 mV or 32 mV grid where the nearest code misses the cell specification. The 0.5 percent accuracy is 21 mV at 4.2 V, so the step is finer than the accuracy and the tolerance is what the cell sees.

The boost mode covers 4.6 V to 5.15 V at up to 1 A for the accessory side. At 94 percent the loss is 0.33 W at 5 W out, which in a 4 by 4 mm body is survivable, but a case that charges two earbuds at once and charges its own cell at 1.5 A is dissipating the charge loss and the boost loss through the same pad, so the two modes are never summed in a thermal budget without checking the derating curve.

IEC 62368-1 CB certification is listed for the part, which shortens the safety file work for a consumer accessory. It does not cover the cell, the connector or the enclosure, so a case built around this charger still needs its own assessment for the battery pack it carries.

The PMID_GOOD pin drives an external P-channel FET so the input can be isolated when a fault appears on the adapter side. That FET is in series with the charge path, so it has to be chosen for the 1.5 A charge current plus the system load, and its on resistance adds directly to the input drop that the tracking loop has to work around.

A 2.5 by 2.0 by 1.0 mm inductor is small enough to fit under a shielding can, and small inductors carry higher resistance. One hundred milliohms of inductor resistance at 1.5 A is 0.225 W, which is more than a third of the total loss at 94.5 percent efficiency, so the inductor is a loss decision and not only a footprint decision.

The boost ceiling of 5.15 V sits below the 5.25 V that a USB port is allowed to reach, so the OTG output can supply a compliant port without a second regulator. The floor of 4.6 V is inside the 4.75 V that a USB host must provide, so the whole boost range is slightly low and a device that checks the port voltage strictly will see a marginal source.

Where this order code fits

Smartwatch and fitness bands, TWS earbud cases, hearing aid charging cases and personal care devices that need a low termination current and a boost for the accessory side are the applications this part was written for. Teams comparing it with a neighbouring part start from our Medical Device Components page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can the boost and the charger run at the same time? The part includes the control to switch between charge and boost mode, so the two are modes and not concurrent paths; a case that must charge its cell and its earbuds together needs the system rail and the boost sequenced by the host.

Does it need an external sense resistor? No. Current sensing for the charge and input loops is inside the part, and the 20 mA termination is measured on the internal path, so the BOM carries the inductor and the capacitors rather than a shunt.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.