Contact Us

BQ25618EYFFR

Brand: Texas Instruments
Texas Instruments BQ25618EYFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25618EYFFR — Power Management & Signal Chain | Superb Automation

BQ25618EYFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25618EYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25618E: a 1.5 A charger built to finish a small pack

The BQ25618EYFFR is an I2C controlled single cell charger with a 1.5 MHz synchronous buck stage, a 4 V to 13.5 V input range, a 22 V absolute maximum rating and a 1.5 A charge current. Efficiency runs at 95.5 per cent at 0.5 A and 94.5 per cent at 1 A, which is the operating point of a wearable or a small handheld rather than a phone.

The reason this part exists is termination. The termination current is 20 mA with a tolerance of plus or minus 10 mA, and on a 150 mAh wearable pack that is 13 per cent of capacity rather than the 30 or 40 per cent a 10 per cent termination rule leaves behind. A product that is expected to run for two days between charges cannot afford to start every cycle three quarters full.

Ship mode takes the battery leakage down to about 7 microamps, and the QON pin brings the part back out of ship mode or forces a full system reset. The battery FET is controlled rather than fixed, so the pack can be disconnected from the system without a separate load switch.

Key data for the BQ25618EYFFR

FunctionI2C controlled single cell buck charger with power path and ship mode
Charge currentUp to 1.5 A
Input range4 V to 13.5 V operating, 22 V absolute maximum
Efficiency95.5 per cent at 0.5 A, 94.5 per cent at 1 A
Voltage accuracyPlus or minus 0.5 per cent, 10 mV steps
Termination20 mA plus or minus 10 mA
Input current limit100 mA to 3.2 A in 100 mA steps over I2C
Temperature profileI2C programmable JEITA, voltage, current and temperature thresholds
Ship modeAbout 7 microamps battery leakage, exited from the QON pin
PackageDSBGA, 30 balls, YFF body, 2.0 mm by 2.4 mm
TemperatureMinus 40 to 85 C operating

Body and ordering data

Two dies share the document, BQ25618E in the 30 ball YFF chip scale body and BQ25619E in the 24 pin RTW QFN at 4 mm by 4 mm. The 2 mm by 2.4 mm body is the one for a board with no room, and the QFN is the one for a board that would rather have the thermal pad than the area saving.

BQ25618EYFFR is the active production row, DSBGA YFF with 30 balls, 3000 pieces on a large tape and reel, SNAGCU finish, moisture level 1 at 260 C, minus 40 to 85 C, marking BQ25618E. The addendum text extract drifts by one row in this table: the status column of the plain string prints blank and the BQ25619ERTWR row shows the DSBGA body and the BQ25618E marking. Read the row against the body column, not against the line order.

Low termination and the taper

Every charge ends with a constant voltage taper, and the current at which the charger decides the pack is full is a choice with a cost. Set it high and the charge ends early with the pack at 85 or 90 per cent. Set it low and the last 10 per cent takes as long as the first 80. On a wearable, that trade runs the other way from a phone: the pack is small, the user charges overnight, and finishing matters more than the last twenty minutes.

The 20 mA figure is only useful if the current measurement is accurate down there. The plus or minus 10 mA tolerance is what makes the figure meaningful, because a 20 mA termination with a 50 per cent uncertainty is really a decision the tolerance makes.

Where it fits in a build

Wearables, hearables, small medical monitors and any single cell product where the pack is under 300 mAh and the charge has to finish. The medical device components page covers the incoming traceability questions these builds raise.

A phone or a tablet with a 4000 mAh pack does not need a 20 mA termination, and the taper from 1.5 A to 20 mA would take hours. Those products use the same family in the higher current members with a termination in the 100 mA class.

The sourcing side of this part is covered on the date code management. For a wearable charger held in a bonded store, that page covers how date codes and moisture levels are tracked from reel to build.

Questions we get on this code

Can the termination be raised? Yes, it is a register. The 20 mA figure is the low end that makes this part useful for small packs, not a fixed value.

What does the QON pin do? It exits ship mode and can force a full system reset, which is how a sealed product with no accessible battery recovers from a hung processor.

Is the 13.5 V input range for USB PD? It covers a high voltage adapter at 9 V or 12 V. Above that the 22 V rating is a survival figure only.

Why is efficiency quoted at 0.5 A rather than at full current? Because the application runs most of its charge at low current, and the light load point is the one that decides the total energy taken from the adapter.