Contact Us

BQ25186DLHR

Brand: Texas Instruments
Texas Instruments BQ25186DLHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25186DLHR — Power Management & Signal Chain | Superb Automation

BQ25186DLHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25186DLHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25186: a 1 A linear charger that works from 3 V to 18 V

The BQ25186DLHR charges one cell at up to 1 A with a power path, ship mode, shutdown mode and a battery tracking input voltage regulation loop. The input window is 3.0 V to 18 V, which is unusually wide for a linear charger, and it is wide on purpose: it has to work from a USB adapter, from an unregulated source that sags, and from another battery.

Battery to battery charging is the case that shapes the input range. A product that charges its own pack from a host pack, a power bank or a vehicle system sees an input that starts at 4.2 V and falls as the source discharges. A charger with a 4.5 V minimum would stop halfway. This one keeps regulating down to 3 V, with a battery tracking loop that keeps the input above the pack voltage rather than at a fixed threshold.

The battery FET is 55 milliohms in the on state and the system can draw up to 3 A through the path, so a processor that bursts does not have to wait for the charger. Ship mode and shutdown mode both cut the pack drain to the microamp class, which is what keeps a shipped product alive on the shelf.

Key data for the BQ25186DLHR

FunctionSingle cell linear charger with power path, ship mode and shutdown mode
Input range3.0 V to 18 V operating, 25 V absolute maximum transient
Charge current5 mA to 1 A, I2C configurable
Voltage accuracy0.5 per cent, 3.5 V to 4.65 V in 10 mV steps
ChemistryLi-ion, Li-polymer and LiFePO4
Battery FET115 milliohms on resistance, 55 milliohms in the low state
System currentUp to 3 A discharge through the path
VINDPMBattery tracking input regulation for high impedance sources
NTCConfigurable charging profile thresholds
ControlI2C, plus a push button input for ship mode exit and reset
PackageWSON, 10 pins, thermal pad, marking B186
TemperatureMinus 40 to 125 C operating

Body and ordering data

BQ25186DLHR is the active production row: WSON DLH with 10 pins, 3000 pieces on a large tape and reel, NIPDAU finish, moisture level 1 at 260 C with no floor life limit, minus 40 to 125 C, marking B186. The .A row carries the same body, the same quantity and the same finish, which is the pattern on every part in this family and the reason a purchase order should name the string and not the family.

The 125 C ceiling is higher than the wearable parts in the same catalogue and is a real advantage on a board where the charger sits near a power stage. The thermal pad is the heat path, and a 10 pin WSON with an unconnected pad is a part that trips its own thermal loop at 500 mA.

What the battery tracking loop buys

A fixed input voltage threshold turns the charge current off whenever the source sags below it, then back on when it recovers, and the result is a visible oscillation on the input and a pack that charges in bursts. Battery tracking sets the threshold relative to the pack voltage, so the charger keeps taking whatever current the source can give without collapsing it. On a solar cell or a wireless receiver, that is the difference between a product that charges in low light and one that does not charge at all.

The 25 V absolute maximum line transient rating exists for the same reason. An 18 V capable input will meet an 18 V source with ringing on connection, and the part has to survive the ring without a clamp in front of it.

Where it fits in a build

Portable instruments, handhelds that charge from another pack, solar and energy harvesting products, and any single cell product with a 12 V accessory socket nearby. The 3 A path and the 125 C rating put it in a different thermal class from the wearable parts. The power management cross reference page lists the parts we compare on input window and path current.

A product that only ever sees a 5 V USB adapter does not need the 18 V window, and the extra input range costs efficiency in the pass device. A product with a 2 cell pack is outside this part entirely.

The sourcing side of this part is covered on the component lead time solutions. For a charger that is specified late in a programme, that page sets out what we check on availability before a build date is promised.

Questions we get on this code

Is the 1 A charge current available from a 12 V source? The current is available and the package is not, because a linear pass device dropping 8 V at 1 A dissipates 8 W. The thermal loop will cut the current to whatever the package can take.

What is ship mode for? It disconnects the pack from the system with the lowest possible drain so a product can sit in a box for a year. The push button brings it back.

Does the LiFePO4 option change the part? No, it is a register setting. The chemistry support is in the setpoint range and the profile, not in a separate order code.

Why does the battery FET resistance change? The two figures are the on resistance in normal operation and in the low resistance state used when the system current is high. The register chooses which applies.