Contact Us

BQ25101YFPR

Brand: Texas Instruments
Texas Instruments BQ25101YFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25101YFPR — Power Management & Signal Chain | Superb Automation

BQ25101YFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25101YFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25101: a 250 mA linear charger for the smallest packs

The BQ25101YFPR charges a single Li-ion or Li-polymer cell at up to 250 mA from an input rated to 30 V, with a 6.5 V overvoltage cut off and a 6 ball chip scale body. It is built for products where the pack is small: a wearable, a sensor node, a disposable style medical patch, a headset.

Two figures describe why this part is chosen instead of a generic linear charger. The first is the termination current, which is settable down to 1 mA. A charger that terminates at 10 per cent of a 250 mA fast charge current stops at 25 mA, and on a 40 mAh pack that leaves a real amount of capacity unused every cycle. The second is the battery output leakage, a maximum of 75 nA. On a product that sits in a drawer for a year, that figure decides whether the pack is still alive when it is taken out.

The charge profile is the standard three phase one: conditioning, constant current, constant voltage, with the termination threshold set by a resistor. A ten hour safety timer backs it up.

Key data for the BQ25101YFPR

FunctionSingle cell Li-ion and Li-polymer linear charger
Charge current10 mA to 250 mA, set by a resistor
Current accuracy10 per cent charge current
Voltage accuracy1 per cent charge voltage
TerminationAdjustable, minimum 1 mA
Battery leakage75 nA maximum with the input removed
Input rating30 V rating, 6.5 V input overvoltage protection
Chemistry options4.35 V on the H variants, 4.30 V on the A variant, 4.2 V on the base
ThermalRegulation at 125 C junction, shutdown at 150 C
PackageDSBGA, 6 balls, YFP body
TemperatureMinus 40 to 85 C operating

Body and ordering data

Six strings share the document: bq25100, bq25101, bq25100A, bq25100H, bq25101H and bq25100L. They differ in the regulation voltage and in the presence of the status output, not in the charge engine. The orderable row on this page is BQ25101YFPR, DSBGA YFP with 6 balls, 3000 pieces on a large tape and reel, SNAGCU finish, moisture level 1 at 260 C with no floor life limit, minus 40 to 85 C, marking 25101.

A 6 ball body at 1.6 mm by 0.9 mm class size is smaller than the passive parts around it. The reel is where the cost sits, and a line that runs small batches should take the 250 piece row rather than open a 3000 piece reel for a hundred units.

The 4.35 V variants and the cell they belong to

A cell specified for 4.35 V holds about 8 per cent more capacity than the same cell specified for 4.2 V, and the charger has to match the cell rather than the other way round. Charging a 4.2 V cell to 4.35 V shortens its life and, at the top of the temperature range, is a safety issue. Charging a 4.35 V cell at 4.2 V is safe and simply leaves capacity unused.

The three voltage options exist because the same die is sold into three different pack specifications. When a product changes cell vendor, the charger string may have to change with it, and that is the change that gets missed between a pack qualification and a production release.

Where it fits in a build

Headsets, wearables, sensor nodes, small medical patches and any product with a pack under 200 mAh. The 75 nA leakage is what makes it usable in a product that is stored for a long time between uses. The medical device components page covers the traceability and packaging questions that come with the patch and monitor market.

For a pack above 500 mAh, 250 mA of charge current is a two hour charge at best and the part is the wrong size. Move to a 1 A part with a power path.

The sourcing side of this part is covered on the date code management. For a small pack built in short runs, that page covers how we handle reel splits and date codes so a two year old charger does not reach a new build.

Questions we get on this code

Can it charge from a 12 V source? The input survives 30 V and the protection cuts at 6.5 V, so a 12 V source is disconnected rather than used. The 30 V figure is a survival rating.

What happens when the battery is missing? The output regulates at the charge voltage and the current falls to the termination level. There is no power path on this part, so a system load in parallel with the pack has to leave enough current for the pack to reach termination within the ten hour timer.

Is 1 mA termination real? It is the minimum the resistor can be set to, and it is accurate enough for a small pack. On a 40 mAh cell, 1 mA is 2.5 per cent of capacity, which is close to the self discharge of the cell itself.

How much does the thermal loop cost me? At 250 mA from 5 V into a 3.7 V cell the dissipation is only about 0.3 W, so the loop rarely acts. It acts on a 9 V source or in a sealed enclosure.