Contact Us

BQ24250RGER

Brand: Texas Instruments
Texas Instruments BQ24250RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24250RGER — Power Management & Signal Chain | Superb Automation

BQ24250RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24250RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24250: 2 A from one input at 3 MHz, in a 4 mm package

The BQ24250RGER is a single input, single cell charger with power path management, an I2C port and a 3 MHz switching stage. The high frequency is the point of the part. At 3 MHz the inductor is small enough to sit under a shield can next to the connector, and the output capacitors shrink with it, which is what a phone board needs when the charger has 20 square millimetres to work in.

The input current limit is selectable at 100 mA, 500 mA, 900 mA, 1.5 A and 2 A, matching the USB and adapter classes the product will see. BC1.2 detection on D+ and D minus identifies the source before the limit is set, so a dedicated charger is not treated like a standard downstream port. Charge voltage, charge current, input limit, the DPM threshold and the safety timer are all programmable over I2C, with resistor defaults for the current that apply before the host writes anything.

The AnyBoot algorithm is worth naming. A deeply discharged pack, or a pack that has gone into protection, does not present a load the charger can recognise. AnyBoot detects that state and applies a controlled recovery rather than refusing to charge, which is what a user experiences as a phone that will not come back on after being left flat.

Key data for the BQ24250RGER

FunctionSingle input 2 A switch mode charger with power path and I2C control
Switching frequency3 MHz synchronous fixed frequency PWM
Charge currentUp to 2 A, resistor default with I2C override
Input limits100 mA, 500 mA, 900 mA, 1.5 A and 2 A selectable
DetectionBC1.2 compatible on D+ and D minus
ProgrammingCharge voltage, charge current, input limit, DPM threshold, OVP threshold, safety timer
Battery recoveryAnyBoot detection for a deeply discharged or protected pack
Charge timerCharge time optimizer to shorten the taper at a given current
PackagesDSBGA 30 ball, 2.40 mm by 2.00 mm, and QFN 24 pin, 4 mm by 4 mm

Body and ordering data

Three dies share the document: bq24250, bq24251 and bq24253. The bq24251 sits at the top of the front page under the vendor end of life status, and that status is a statement about new programs rather than about stock. The bq24250 and bq24253 remain the active rows for new work.

BQ24250RGER is the QFN body, 24 pins, 4 mm by 4 mm, in a large reel. The chip scale option is the 30 ball DSBGA at 2.40 mm by 2.00 mm. Both bodies carry the same die, so a move between them is a change of copper, not of function. Ask for the row when you quote, because the two bodies are quoted at different prices and only one of them suits a board that is already laid out for the other.

What 3 MHz costs you

A 3 MHz converter trades switching loss for size. Every transition charges and discharges the gate of the FETs, and the faster the stage runs the more of the input power goes into that rather than into the cell. The efficiency at 2 A is still good, but the light load behaviour and the thermal margin at the top of the current range are different from a 1.5 MHz part of the same class.

It also puts demands on the input capacitor and on the routing of the return path. At 3 MHz a 10 mm loop from the input capacitor to the FETs is a measurable inductor, and the ringing shows up as conducted emissions at the third and fifth harmonic. A part that works on the bench and fails radiated emissions later usually has that loop to blame.

Where it fits in a build

Phones, portable media players, handheld instruments with a single cell and a USB port. The BC1.2 detection is worth having when the product charges from whatever cable the user finds, because a 2 A limit applied to a 500 mA port is a support ticket. For products that charge from a fixed adapter and never from a computer port, the selectable limits are less useful.

When this string is short, the component lead time solutions page sets out how we check what a substitute has to match on the input detection side before a part is offered as an alternative.

The sourcing side of this part is covered on the power management cross reference. For a platform moving from this die to a newer member of the family, that page lists the pins and registers we compare before any substitution is proposed.

Questions we get on this code

Is the 2 A charge current available at 3 MHz without a heatsink? With adequate copper under the QFN thermal pad, yes, and with the thermal loop cutting in if the junction climbs. On the chip scale body the copper is the only heatsink there is.

What does the safety timer do if the host does not write it? The resistor defaults set a timer, and the charge terminates when it expires. A host that never writes the register still gets protection, which is the reason the defaults exist.

Does AnyBoot work with a pack in protection mode? It recovers a pack whose voltage has fallen below the normal precharge threshold, provided the protection FET in the pack is on. A pack that has latched its own protection off needs the pack side to release first.

Can I run it without I2C? Yes, the resistor defaults set current and voltage, and the part charges without any bus traffic. What is lost is the ability to change the limit when the source changes.