BQ24072RGTR
Product Specifications
BQ24072RGTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24072RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24072RGTR: 1.5 A charge with the system held above the battery
The BQ24072RGTR is the base member of the BQ2407x family, a standalone charger for one Li-Ion cell with a power path. It charges at up to 1.5 A from a USB port or a wall adapter and runs the system from the input while it charges, so the product starts on a flat pack. The system output on this member tracks the battery voltage with a 225 mV offset, which is the simplest of the behaviours in the family and the one that keeps the system rail as low as the cell allows.
Input handling is the reason this family is chosen over a plain charger. The USB input limit is selectable between 100 mA and 500 mA, and the 100 mA setting is there to keep the product inside the USB specification on an unknown host port. Input voltage based dynamic power management watches the input and reduces the load if the source sags, which is what stops a weak USB port or a long cable from collapsing the rail in the middle of a charge. The input is rated to 28 V with overvoltage protection, so a wrong adapter is a disconnect rather than a dead board.
The family has five members and they are not interchangeable. The BQ24072 regulates the system output to the battery voltage plus 225 mV, the BQ24073 and BQ24074 regulate it to 4.4 V, and the BQ24075 regulates it to 5.5 V. The BQ24078 charges to 4.35 V, and the BQ24079 to 4.1 V. The BQ24074 and BQ24075 add a programmable termination current, and the BQ24072 has a voltage based termination. Choosing between them is a system decision about the rail the load needs, not a price decision.
Key data for the BQ24072RGTR
| Function | Standalone single-cell linear charger with dynamic power path management |
| Charge current | Up to 1.5 A, set by the ISET resistor, with a current monitoring output |
| System output | Battery voltage plus 225 mV on this member |
| Battery regulation | 4.2 V on this member, 4.35 V on the BQ24078 and 4.1 V on the BQ24079 |
| Overvoltage protection | 6.6 V on this member, 10.5 V on the BQ24074 |
| USB limits | 100 mA or 500 mA selectable, with VIN-DPM protection against poor sources |
| Input rating | 28 V, with overvoltage protection on the input |
| Termination | Voltage based on this member, programmable current on the BQ24074 and BQ24075 |
| Timers | Programmable pre-charge and fast charge safety timers |
| Enable pin | Internally pulled down with about 285 kOhm, so it must not be left unconnected |
Body and ordering data
| Body in this code | 16-pin VQFN, the RGT outline, 3.00 mm by 3.00 mm |
| Thermal path | Exposed pad to the ground pour; at 1.5 A the linear element is the heat source |
| Pins | IN, OUT, BAT, ISET, ILIM, TMR, CE, TS, CHG, PGOOD, VSS and the SYSOFF pin where the member has one |
| Battery disconnect | SYSOFF input on the BQ24075 and BQ24079, not on this member |
| Carrier | Tape and reel, count per reel read from the addendum row of the exact string |
| Document | SLUS810N, revised October 2021 |
Reading the code before you buy it
Two letters decide almost everything here. The number after BQ2407 sets the system output voltage and the termination method, and the letters after it set the body and the packing. Because the five members share one document, one pinout drawing and one footprint, a substitution looks safe on the drawing and fails in the product: a 5.5 V system output on a load rated for 4.4 V is a fault that appears only under load, and a voltage terminated member on a product that needs a low termination current will hold a charge that never finishes.
The second trap is the enable pin. It has an internal pull-down of about 285 kOhm and the document warns against leaving it unconnected. On a board where the host never drives that pin, the charger stays off and the product appears dead with a good battery. That is a drawing omission rather than a part problem, and it is the kind of fault our incoming inspection plan cannot catch, because the part is correct.
Dissipation deserves the same attention as on any linear charger. At 1.5 A from a 5 V adapter into a 3.7 V cell the pass element carries nearly 2 W, and the thermal loop will reduce the current rather than let the die run away. A 3 mm square body needs the exposed pad soldered to a real copper area; a footprint with a thin trace to the pad gives a charger that works on the bench and folds back inside the enclosure.
Where it fits in a build
Portable instruments, handheld terminals, wireless speakers, medical monitors and single-cell products that charge from USB and must run while charging are the natural fit. The programmable input limit also suits products that ship with a wall adapter of unknown quality, because VIN-DPM protects the system rail when that adapter sags under load.
Products that need a fuel gauge, a boost rail or a second cell are outside this part, and a product that needs to disconnect the battery from the system when the pack is removed should move to the BQ24075 or BQ24079 members with SYSOFF. Our safety stock planning page explains how we hold the siblings of a family like this so a build is not stopped by one order code going short.
Questions we get on this code
Why does the system rail sit only 225 mV above the battery? Because the pass element is a linear regulator and every millivolt above the cell is heat. This member is the right choice when the load runs fine at cell voltage and the priority is efficiency and low dissipation. A load that needs 5 V has to use the BQ24075 member or a separate boost converter.
Can the charge current be monitored? Yes, the ISET pin doubles as a current monitor during the constant voltage phase, which lets a host estimate the taper without a sense resistor. The relation between the pin voltage and the current is in the electrical table for the ISET resistor actually fitted.
What happens with no battery connected? The power path keeps the system alive from the input, and the charger terminates on its timer. That behaviour is what makes the family usable on a product that ships without a pack installed.
Is the input protected against a reversed adapter? The input is rated to 28 V with overvoltage protection, but reverse polarity is a different condition and needs its own protection at the connector. A 28 V rating is not a reverse voltage rating.