BQ24045DSQR
Product Specifications
BQ24045DSQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24045DSQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24045DSQR: 1 A, 4.35 V chemistry and a 30 V input in a 2 mm body
The BQ24045DSQR is the 4.35 V member of the BQ2404x family, a single-input linear charger for one Li-Ion or Li-Pol cell that takes either a USB port or a wall adapter and delivers up to 1 A. The die carries the pass FET and the current sense, so the charge current is set by one resistor on the ISET pin and the pre-charge and termination thresholds by a second resistor, without a sense resistor in the battery path.
What separates this member from its siblings is the regulation voltage. The BQ24040 and BQ24041 regulate to 4.20 V, and the BQ24045 regulates to 4.35 V for the higher voltage cells that some handset and wearable packs use. The three parts share a body, a pinout and a document. Putting a 4.35 V member on a 4.20 V cell is an overcharge that the cell data sheet will not support, and nothing on the board announces the difference, so the order code is the only place the distinction lives.
The input side is built for cheap adapters. The input is rated to 30 V, and the overvoltage protection trips at 6.6 V on the BQ24045 rather than the 7.1 V of the BQ24041. That is a low ceiling, and it is deliberate: an unregulated adapter that rises above 6.6 V would otherwise push the linear pass FET into a dissipation it cannot survive, so the part disconnects instead. A product that expects a 9 V or 12 V adapter is not a fit for this family.
Key data for the BQ24045DSQR
| Function | Single-input single-cell Li-Ion and Li-Pol linear charger with auto start |
| Charge current | Up to 1 A, set by the ISET resistor |
| Regulation voltage | 4.35 V on this member, 4.20 V on the BQ24040 and BQ24041 |
| Voltage accuracy | 1 percent charge voltage accuracy, 10 percent charge current accuracy |
| Input current limit | 100 mA or 500 mA selected by the ISET2 pin |
| Input rating | 30 V absolute, overvoltage protection at 6.6 V on this member and 7.1 V on the BQ24041 |
| Termination | Programmable on this member, with a fixed 10 hour safety timer |
| Thermal behaviour | Regulation of the charge current at 125 C die temperature, shutdown at 150 C |
| JEITA | Half fast charge current when cold, 4.06 V regulation when hot, through the battery NTC |
| Input protection | Input voltage dynamic power management, OUT short circuit protection, ISET short detection |
Body and ordering data
| Body in this code | 10-pin WSON, the DSQ outline, 2.00 mm by 2.00 mm |
| Thermal path | Exposed pad, soldered to copper; the linear pass element carries the input to battery difference |
| Pin count | Ten pins including TS, ISET, ISET2, PRETERM, CHG, PG and the input and output pins |
| Certification | IEC 62368-1 CB certification listed for the BQ24040 and the BQ24045 |
| Carrier | Tape and reel, count per reel read from the vendor addendum row of the exact string |
| Document | SLUS941H, revised February 2021 |
Reading the code before you buy it
The DSQ string is the 2 mm square body. The same circuits also ship in other bodies with different suffixes, and the pin list is not identical between them, so a substitute has to be checked pin by pin rather than by current rating. The three members of the family also differ in whether the termination threshold is programmable, whether the timer is fixed and whether the part has the timer disable mode that lets a product run with the pack removed and a thermistor on the board.
The resistor values carry a history worth knowing. The vendor revision notes record the nominal ISET resistor changing from 49.9 kOhm to 10.8 kOhm, and the short circuit test condition changing from 600 Ohm down to 540 Ohm. A board copied from an older reference will therefore have a resistor that sets a different current from the one in the current document. Our BOM scrubbing page covers how we catch that class of mismatch before a build starts.
The last item is the thermal budget. At 1 A from a 5 V adapter into a 3.7 V cell the pass element dissipates about 1.3 W, and the part protects itself by folding the current back at 125 C rather than by failing. A 2 mm square body reaches that temperature quickly unless the pad has copper and vias behind it, so the charging time in a closed plastic case is a thermal result, not just a setting.
Where it fits in a build
Wireless headsets and earbud cases, portable medical devices, handheld instruments, wearable sensors and small consumer products all fit the part, and the 2 mm body is what makes it usable in a case that has no room for a charger circuit. The auto start function exists for the production line: the part begins charging as soon as a source is applied without a host command, which is what a test fixture needs.
Where it does not fit is any product that has to run its system while the cell is deeply discharged, or one that charges from a source above 6.6 V. The first needs a power path part, and the second needs a charger with a higher input rating. Our medical device components page lists the parts we hold for that market segment and the qualification records that go with them.
Questions we get on this code
Can I use the BQ24040 instead? Only if the cell is a 4.20 V chemistry. The two parts are otherwise similar and share the document, which is exactly why substitutions get made by mistake. The regulation voltage difference of 150 mV is the whole reason to check.
What does the JEITA behaviour do in a cold store room? Below the cold threshold the fast charge current is halved, and above the hot threshold the regulation voltage drops to 4.06 V. A product that has to be fully charged in a cold environment will take longer, and a product charged at high temperature will stop at a lower voltage by intent.
Is there a fuel gauge here? No. The part terminates on current and time and reports charge and done. A product that has to display a percentage needs a separate gauge on the battery, and that part has its own accuracy and calibration story.
How is the input current limit changed? By the ISET2 pin level, between 100 mA and 500 mA. There is no register, so a product that has to negotiate higher current from a USB-C source needs a different front end; this family stops at the 500 mA USB limit.