BQ24031RHLR
Product Specifications
BQ24031RHLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24031RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24031RHLR: a charger that keeps the system running on a flat battery
The BQ24031RHLR is a member of the bq2403x family, a single-cell Li-Ion charger with a power path. The difference against a plain charger is what happens at the output: instead of charging the cell and letting the system sit on the battery node, the device runs the system from the adapter or from the USB port while it charges the cell separately. A product with a dead pack therefore turns on the moment the adapter is plugged in, and a product with no pack at all still runs.
Two inputs are managed automatically. The adapter and the USB port are both connected, the device picks the adapter, and the USB input is left current limited at either 100 mA or 500 mA depending on the ISET2 pin, which is what keeps an unknown host port from being overloaded. Total current available to the system and the battery is up to 2 A. When the input cannot supply both, dynamic power path management reduces the charge current first so the system rail does not collapse, and the power supplement mode lets the battery make up the difference instead of browning the system out.
There is a 3.3 V linear regulator on the die as well, rated 20 mA, intended for the small housekeeping loads that would otherwise need their own part. A 0.1 microfarad output capacitor is recommended but not required. That regulator is only active when an input source is present, so it cannot be used as a always-on rail for a real time clock.
Key data for the BQ24031RHLR
| Function | Single-cell Li-Ion charger with dynamic power path management and power supplement |
| Inputs | AC adapter and USB, selected automatically, adapter wins when both are present |
| USB current limit | 100 mA or 500 mA, set by the ISET2 pin level |
| Total current | Up to 2 A shared between the system output and the battery |
| Charge voltage | 4.1 V, 4.2 V or 4.36 V depending on the member and the option |
| On die regulator | 3.3 V at 20 mA, active only with an input source present |
| Quiescent current | 200 microamps with the charger disabled and no loads on OUT or the regulator |
| Protection | Thermal regulation of the charge current, short circuit, reverse current blocking |
| Absolute maximum | 7 V on BAT, OUT, CE, DPPM, ACPG, PSEL, ISET1, ISET2, STAT1, STAT2 and TS |
| Status outputs | Two open drain lines for charge and fault, plus power good for the adapter and for USB |
Body and ordering data
| Body in this code | 20-pin VQFN, the RHL outline, 4.50 mm by 3.50 mm |
| Thermal path | Exposed pad under the die, soldered to the ground pour; the linear pass FET carries the dissipation |
| Family members | bq24030, bq24031, bq24032A, bq24035 and bq24038, same body, different charge voltage options and pin behaviour |
| Carrier | Tape and reel, count per reel read from the vendor addendum row of the exact string |
| Document | SLUS618I, revised December 2014 |
Reading the code before you buy it
The family shares one body and one pin list, and the charge voltage option is the difference that matters most. A 4.1 V member on a 4.2 V cell leaves capacity unused, and a 4.36 V member on a 4.2 V cell overcharges it. The pin functions also shift between members: the bq24038 rows in the same document are listed as regulated to 4.4 V with 4.2 V or 4.36 V selectable, which is a different behaviour on the same footprint. Buyers who treat the family as one part discover this at incoming inspection.
The DPPM pin is the second difference. The threshold is set by an external divider and it decides when the charge current starts to back off. A divider copied from a different member of the family sets a threshold for the wrong scale factor, and the symptom is a charger that folds back early or never folds back at all. Our pin to pin cross reference page lists the comparisons we run before offering one member in place of another.
Dissipation has to be checked against the total current, not the charge current. With 2 A shared and a 5 V adapter, the linear element can carry several watts into a 3.5 mm by 4.5 mm body, and the thermal regulation loop will reduce the charge current to protect the die. That is a feature, but it changes the charge time an end customer sees.
Where it fits in a build
Smart phones, handheld terminals, portable instruments, media players and any single-cell product where the system has to run from a weak or missing battery are the vendor's own list. In our own builds the part turns up in battery powered test equipment and handheld terminals that charge from either a wall adapter or a laptop port, because the automatic source selection removes a switch and a control line from the board.
Where the product needs a fuel gauge, a boost for a white LED string, or a regulated system rail above the battery voltage, those are separate parts and the power path has to be planned around them. Our one stop BOM sourcing page covers how we group that class of parts on one line card so a single short part does not hold a build.
Questions we get on this code
Can both inputs be connected at the same time? Yes, and the adapter wins. The USB port is then held at its 100 mA or 500 mA limit but is not used as the charge source, so a product that also needs the USB data lines alive has to account for the port staying enumerated while the adapter carries the load.
What happens if the system load exceeds what the input can supply? The charge current drops first. If the load still pulls the system rail down to the DPPM threshold, the battery supplements the missing current instead of the rail collapsing. This is the behaviour that keeps a radio transmit burst from resetting the product on a 500 mA port.
Is the 3.3 V regulator good enough for a microcontroller? It is 20 mA and only present when an input source is connected. A microcontroller that has to stay alive on battery power needs its own regulator from the battery node.
Does the part need a thermistor? The TS pin exists on the family and expects the usual divider. On a pack without a thermistor the pin has to be biased to a valid window, otherwise the charger reports a temperature fault and never starts. That bias is one resistor pair the BOM has to carry.