AMC1311BQDWVRQ1
Product Specifications
AMC1311BQDWVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC1311BQDWVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC1311BQDWVRQ1 automotive isolated amplifier with a two volt high impedance input for voltage sensing
The AMC1311BQDWVRQ1 is the automotive grade B member of the AMC1311 family, an isolated amplifier with a two volt high impedance input and a fixed gain of one, intended for isolated voltage measurement through a resistive divider rather than for shunt current measurement. It is qualified to AEC-Q100 grade 1 over minus 40 to plus 125 degrees ambient and is certified for reinforced isolation of 5 kilovolts RMS with a working voltage of up to 1500 volts RMS.
The high impedance input is the difference that matters. A current sensing amplifier presents a low impedance and expects millivolts from a shunt; this part presents a high impedance and expects up to two volts from a divider, which means the divider resistors can be large enough to keep the dissipation and the leakage within what a high voltage board can tolerate. The B grade prints offset error of 1.5 millivolts maximum, offset drift of 10 microvolts per degree maximum and gain error of 0.2 percent maximum.
Key parameters taken from the AMC1311BQDWVRQ1 document
| Input range | Plus or minus 2 V, high impedance, intended for a resistive divider |
| Gain | Fixed 1 |
| Offset error | 1.5 mV maximum on the B grade, 9.9 mV on the standard grade |
| Offset drift | 10 microvolts per C maximum on the B grade, 20 typical on the standard grade |
| Gain error | 0.2 percent maximum on the B grade, 1 percent on the standard grade |
| Gain drift | 30 parts per million per C typical |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 C ambient |
| Functional safety | Documentation available to support a functional safety system |
| Isolation | Reinforced, 5 kV RMS per DIN EN IEC 60747-17 and UL1577 |
| Working voltage | Up to 1500 V RMS |
| Input impedance | High, so a large value divider can drive it without loading error |
| Package | SOIC-16 wide body DW, tape and reel |
| Order code facts | AMC1311BQDWVRQ1, DW body, tape and reel, automotive grade 1, B performance grade |
| Family | The standard AMC1311 and the B grade share the package and differ in the error terms |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The divider is the accuracy limit on this part, and it is worth choosing it deliberately. A two volt input across a divider from a 800 volt bus means the divider ratio is 400 to 1, and the tolerance and the temperature coefficient of the two resistors set the accuracy of the measurement before the amplifier contributes anything. The high input impedance means the divider can be made from large values, which keeps the dissipation low, but large values bring leakage and settling into the picture; the document prints the input impedance so the settling time can be calculated rather than guessed.
Reinforced isolation at 5 kilovolts RMS with a 1500 volt working voltage is what allows this part on a mains connected or traction bus without a second barrier. The certification is per the current standard, DIN EN IEC 60747-17, and the working voltage figure is the one a safety reviewer will use, not the peak withstand. A board that quotes the withstand voltage as the working voltage in its safety file is the most common error in this area, and it is caught at the review rather than at the bench.
The functional safety note in the document is a documentation statement rather than a feature: the vendor supplies the material a safety case needs, and the engineering team still has to build the diagnostics. In practice that means a plausibility check between this channel and a redundant measurement, a check that the output sits inside the expected window, and a decision about what the system does when the two disagree. None of that is in the part, and all of it is in the certification file.
Because the output is a single ended signal referenced to the low side ground with a gain of one, the interface to the controller is direct: two volts in, two volts out. That makes the part easy to integrate and easy to mis-scale, because a firmware written for a gain of eight part will read one eighth of the actual voltage. The scaling constant should be written down once, next to the divider ratio, and checked on the first article against a calibrated source at two points.
- Divider ratio and tolerance verified against a calibrated source at two voltages, at 25 degrees and at both temperature extremes.
- Offset and gain measured at the low end of the input range, where a ten microvolt per degree drift is a larger fraction of the reading.
- Settling time with the actual divider resistance, since a large value divider and a small filter capacitor form a slow node.
- Isolation working voltage and creepage verified against the safety file, on every layer of the board.
- Plausibility and redundancy check behaviour when this channel and the backup disagree.
- Functional safety documentation set complete, with the vendor material referenced by document number.
Which projects this part fits
This part fits automotive traction inverter DC link voltage sensing, battery pack and bus voltage measurement, onboard charger input voltage, photovoltaic string voltage, motor drive DC bus monitoring and any isolated voltage measurement where a divider and a reinforced barrier are both required. For SUPERB customers in automotive power electronics and energy conversion it is the counterpart to the current sensing amplifier on the same board, and using one family for both channels keeps the error budget and the board rules consistent.
Questions that come up before a purchase order is released
Can this part measure current as well as voltage?
Not directly, because the two volt input and the gain of one are chosen for a divider. A shunt produces tens of millivolts and would use a small fraction of the range, which throws away resolution. The same family tree contains the 250 millivolt current sensing amplifiers, and the two are used side by side on a drive board.
What does the B grade change?
The published error terms: offset from 9.9 to 1.5 millivolts maximum, offset drift from 20 typical to 10 maximum microvolts per degree, and gain error from 1 to 0.2 percent maximum. The package and the isolation are unchanged, so a board can move between grades without a board change and the decision is made on the error budget.
Why does the working voltage differ from the rated isolation?
They are different quantities. The rated isolation is a withstand that the barrier survives in a test, and the working voltage is the level it can hold continuously over life. A safety file has to use the working voltage, and the document prints both so there is no ambiguity.
What divider values are practical?
The high input impedance allows large values, and the practical limit is leakage and settling rather than loading. On a high voltage board the divider also has to survive the voltage across each resistor, so the choice is usually two or more resistors in series per leg, with the voltage rating per part taken from the resistor document rather than assumed.
Is the automotive row required for a 48 volt system?
Not strictly, because 48 volts is inside the working voltage of the standard grade as well. The automotive row is chosen for the qualification and the change control that a vehicle program requires, and for the temperature grade. The isolation and electrical performance are the same story told with tighter numbers in the B grade.
How SUPERB handles this line
We supply the AMC1311BQDWVRQ1 on original tape and reel with the automotive and performance grades verified on the label, and we can supply the vendor document number with the shipment for the safety file. Where the board is comparing isolated voltage sensing options, the power management cross reference page lists the families by input range and isolation class. For continuity across an automotive program, component obsolescence management covers the options, and incoming inspection plan covers the arrival checks.