AMC1300BDWVR
Product Specifications
AMC1300BDWVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC1300BDWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC1300BDWVR isolated amplifier with a 250 millivolt input, 8.2 gain and reinforced isolation
The AMC1300BDWVR is the B grade member of the AMC1300 isolated amplifier family in the wide body SOIC, with a 250 millivolt input for shunt current measurement, a fixed gain of 8.2 and a reinforced isolation barrier certified to 7071 volts peak. The B grade is the tighter of the two published grades, and the difference is entirely in the error terms rather than in the isolation or the bandwidth.
The B grade prints offset error of 0.2 millivolts maximum against 2 millivolts on the standard grade, offset drift of 0.9 microvolts per degree against 4, gain error of 0.3 percent against 1 percent, and gain drift of 30 parts per million per degree maximum against 50 typical. Nonlinearity is 0.03 percent maximum and common mode transient immunity is 100 kilovolts per microsecond minimum. Those numbers put this part in a different class from a general purpose isolated amplifier, and they are the reason it appears in current control loops rather than only in monitoring.
Key parameters taken from the AMC1300BDWVR document
| Input range | Plus or minus 250 mV, optimised for a shunt resistor |
| Gain | Fixed 8.2 |
| Offset error | 0.2 mV maximum on the B grade, 2 mV on the standard grade |
| Offset drift | 0.9 microvolts per C maximum on the B grade, 4 microvolts per C on the standard grade |
| Gain error | 0.3 percent maximum on the B grade, 1 percent on the standard grade |
| Gain drift | 30 parts per million per C maximum on the B grade, 50 typical on the standard grade |
| Nonlinearity | 0.03 percent maximum |
| Common mode transient immunity | 100 kV per microsecond minimum on the B grade |
| High side supply | 3.3 V operation on the B grade |
| Isolation | 7071 V peak reinforced per DIN VDE V 0884-11, 5 kV RMS per UL1577 |
| Emissions | Meets CISPR-11 and CISPR-25 limits, which matters for a product with a radio nearby |
| Diagnostics | Common mode overvoltage detection and missing high side supply detection |
| Temperature | Minus 55 to plus 125 C on the B grade, minus 40 to plus 125 C on the standard grade |
| Package | SOIC-16 wide body DW, this code is the tape and reel DW version |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The two diagnostic features are the reason this part is easier to make safe than a plain amplifier. A missing high side supply produces a defined output rather than a floating one, and a common mode overvoltage on the shunt node is flagged rather than silently clipped. In a drive, both of those conditions are what a service engineer would otherwise have to find by inference, and the document prints the output behaviour in each case so the firmware can classify the fault instead of reporting a generic current error.
Gain drift of 30 parts per million per degree is the number that decides whether a current loop stays calibrated over the life of a machine. Over a hundred degree swing that is 0.3 percent, which is smaller than the shunt drift and smaller than the reference drift in most boards, so at that point the shunt becomes the accuracy limit. A board that already has a 0.5 percent shunt and a 1 percent reference gains nothing from the B grade and should take the standard grade instead, which is a cheaper and more available part.
The high side runs on 3.3 volts on the B grade, which reduces the isolated supply requirement and the dissipation on the hot side of the barrier. That is a real advantage on a board where the isolated supply is a small transformer driven from a gate driver supply, because the load on that supply drops with the voltage. The trade is that the input common mode range is tied to that rail, so a shunt that sits at a high potential with respect to the high side ground needs the divider or the level shift the document describes.
Electromagnetic compliance is worth a sentence because it is often discovered late. An isolated amplifier switches internally to transfer the signal, and the switching edge radiates. The document states that the part meets CISPR-11 and CISPR-25 limits, which is a claim about the part in a reference routing, not about the customer's board. Where the product carries a radio or a CE mark, the first article emission scan should include the isolated amplifier active and a shunt current flowing, because a static test will not show the transfer activity.
- Offset, gain and drift over the full printed temperature range, on the first article, against the B grade limits.
- Output behaviour with the high side supply removed, recorded for the fault classification table.
- Common mode overvoltage flag asserted with the shunt node driven above the printed window.
- Noise and linearity at the current level the loop actually regulates at, not only at full scale.
- Radiated emissions with the part active and current flowing, against the product's own limit.
- Isolation barrier routing on every layer, including plane splits, against the printed creepage.
Which projects this part fits
This part fits servo and inverter phase current control, motor drive torque control where ripple matters, photovoltaic and energy storage current measurement, charger current regulation, and industrial power supplies with a tight current loop. For SUPERB customers building drives, chargers and power conversion hardware it is the choice when the accuracy of the current measurement is what limits the performance of the machine rather than the resolution of the controller.
Questions that come up before a purchase order is released
When does the B grade pay for itself?
When the error budget is dominated by the amplifier rather than by the shunt or the reference. In a loop that regulates torque or charge current to a fraction of a percent, the tighter offset and gain drift remove a calibration step and a temperature compensation table. In a monitoring application that only needs a few percent, the standard grade is the better buy and is usually easier to find in stock.
What is the difference from the AMC1100?
The family and the function are similar and the isolation and gain differ. The AMC1300 family runs at a gain of 8.2 with a 3.3 volt high side on the B grade and carries the reinforced rating, while the AMC1100 is a gain of 8 basic isolation part. A board cannot swap between them without checking the input range and the isolation certification the product needs.
Does the part need an external clock?
No, the transfer is internal and the part is an analogue in, analogue out device, so it drops into an existing converter input without a digital filter. The counterpart family with a digital output exists for boards that prefer to filter in the controller, and the choice is usually made on whether the loop runs in hardware or in firmware.
How is the missing supply diagnostic used?
The output takes a defined state when the high side supply is absent, and the firmware treats that state as a sensor fault rather than as a current reading. That distinction matters in a drive, because a plausible but wrong current reading at standstill can command torque in the wrong direction, while a flagged fault stops the machine safely.
What package options exist for this family?
The wide body SOIC is the standard isolated package for this family and the one printed for this code, with the tape and reel suffix. The family also carries narrower and wider variants with different isolation ratings, and the certification the product needs decides which one is acceptable rather than the footprint.
How SUPERB handles this line
We supply the AMC1300BDWVR from original tape and reel with lot traceability, and we verify the grade letter and the body before the parts are booked to a line. Where the board is comparing isolated amplifiers, the power management cross reference page lists the families by input range, gain and isolation class. Where continuity is the concern, component obsolescence management covers the long term options, and incoming inspection plan covers the arrival checks.