Contact Us

ADS62P42

Brand: Texas Instruments
Texas Instruments ADS62P42 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS62P42 — Power Management & Signal Chain | Superb Automation

ADS62P42

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS62P42 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS62P42: dual 14 bit 65 MSPS converter, the slowest and quietest member of the ADS62P4X family

ADS62P42 is the 65 MSPS member of the dual 14 bit family, with the same digital block and the best signal to noise ratio in the range in a QFN body of 64 pins. The ADS62P42 is the 65 MSPS member of the dual 14 bit family and the quietest of the four, with 94 dB of SNR at a 10 MHz input against 88 dB at the 125 MSPS member. Analog power is 515 mW, crosstalk between channels is 95 dB, and both channels share the digital block that offers offset correction, fine gain in 0.05 dB steps, decimation by 2, 4 or 8 and built in or user programmed 24 tap filters. The body is a 64 pin QFN of 9 mm by 9 mm.

Order code and package

Order codeADS62P42
Channelstwo, simultaneous
Resolution14 bit
Maximum sample rate65 MSPS
Family positionslowest of four, 125, 105, 80 and 65 MSPS
Analog power515 mW at 65 MSPS
Digital blockoffset correction, fine gain, decimation, 24 tap filters
Decimationby 2, 4 or 8
Output interfaceDDR LVDS or parallel CMOS
Crosstalk95 dB
Package64 pin QFN, 9 mm by 9 mm
DocumentSLAS561C, July 2007, revised February 2012

Electrical parameters that decide the application

SNR at a 10 MHz input94 dB, the best in the family
Power per sample pair7.9 nJ at 65 MSPS
Data rate at full rate1.82 Gbps per channel
Decimated rates32.5, 16.25 and 8.125 MSPS
Coarse gain3.5 dB
Fine gainup to 6 dB in 0.05 dB steps
Filter length24 taps
Input range2 V peak to peak differential
Clock amplitude400 mV peak to peak minimum
Temperatureminus 40 to 85 C
Referenceinternal or external
Package sharingsame body as the faster members

Points to check before this part goes on a BOM

This is the member where the noise floor is the best and the bandwidth is the smallest. A band under 32.5 MHz gets 94 dB of SNR at 65 MSPS, and the same band captured at 125 MSPS would give 88 dB, so choosing the faster part for headroom costs 6 dB of dynamic range. In a narrowband measurement that is the whole trade and the slower part wins.

515 mW of analog power is the lowest of the four members, and with decimation by 8 the output rate is 8.125 MSPS, which a small microcontroller with a parallel port can capture. This combination, low power and a low output rate, is why the member survives in portable and battery powered instruments even though its document dates from 2007.

The digital filter is what makes the low output rate usable. Decimating by 8 without a filter would alias everything above 4 MHz back into the band, so the 24 tap response is doing real work rather than saving pins alone. A custom response loaded from firmware can be shaped for a specific sensor band, which is common in medical and seismic work.

Ninety five dB of crosstalk means the two channels can be used for a differential or a phase coherent pair. It also means an overload in one channel does not corrupt the other, which matters when one channel watches a large stimulus and the other a small response, as in a pulse echo measurement.

Fine gain in 0.05 dB steps exists to match the channels against each other. For a phase coherent pair, a gain difference of a tenth of a dB is an image at minus 60 dB, and the fine step is the tool that gets the pair matched without trimming resistors on the board.

The 2 V peak to peak differential input and the 3.5 dB coarse gain step are the same front end as the rest of the family, so an amplifier stage proven at 125 MSPS carries down to this part without change. That is the practical reason to keep one family across a product line rather than mixing vendors.

For a long life programme this member is the one most likely to stay in production, because it is the lowest power and the one used in instruments with slow refresh cycles. A socket built for it also takes the faster members, so a performance upgrade later does not need a board change.

The on chip decimation is what makes the 8.125 MSPS output usable in a low power instrument: without the filter, everything above 4 MHz would fold back into the band. A custom 24 tap response loaded from firmware can be shaped to the sensor band, which is common in seismic and medical work where the wanted band is a narrow slice of the analog bandwidth.

Where this order code fits

This order code belongs on medical imaging front ends, ultrasound receive channels, geophysical and seismic acquisition, and industrial vibration analysis where the band of interest is narrow and the dynamic range is the whole point. It is also the member to choose when a board must run from a limited power budget and still hold 14 bit resolution. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Why choose 65 MSPS when faster members exist? Because the slower member measures 94 dB of SNR against 88 dB at 125 MSPS, and it uses 515 mW against 799 mW. A narrowband application gains both ways.

Can the output rate be reduced further? Yes, decimation by 2, 4 or 8 gives 32.5, 16.25 or 8.125 MSPS with the on chip filter providing the alias rejection.

Are the two channels matched? They sit on one die with 95 dB of isolation, and the fine gain step of 0.05 dB is there to trim the remaining difference in firmware.

SUPERB holds this order code with date codes and packing stated on the offer, and the Component Obsolescence Management page covers how to keep a low power dual channel socket alive over a long product life.