Contact Us

ADS5482

Brand: Texas Instruments
Texas Instruments ADS5482 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS5482 — Power Management & Signal Chain | Superb Automation

ADS5482

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS5482 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS5482: 16 bit 105 MSPS converter in the middle of the ADS548x family

ADS5482 is the 105 MSPS member of the 16 bit family, on the same 64 pin body as the 80 MSPS and 135 MSPS parts and on the same 5 V analog rail in a QFN body of 64 pins. The ADS5482 is the middle member of a three part 16 bit family: 80 MSPS, 105 MSPS and 135 MSPS, all in a 64 pin QFN with an exposed pad and all running from a 5 V analog supply and a 3.3 V analog and digital supply. Outputs are LVDS compatible, the analog input buffer and the reference generator are on chip, and total power is 2.2 W with a 70 mW power down state. The family document is SLAS565C.

Order code and package

Order codeADS5482
Channelsone
Resolution16 bit
Maximum sample rate105 MSPS
Family rates80, 105 and 135 MSPS across ADS5481, ADS5482 and ADS5483
Analog supply5 V and 3.3 V
Digital supply3.3 V
Output interfaceLVDS compatible
Input bufferintegrated
Referenceinternal generator
Package64 pin QFN with exposed pad, 9 mm by 9 mm
DocumentSLAS565C, June 2008, revised October 2009

Electrical parameters that decide the application

Total power2.2 W at rated sample rate
Power down70 mW
Power per sample21 nJ at 105 MSPS
SFDR, family headline95 dBc at 70 MHz and 135 MSPS
SNR, family headline78.6 dBFS at 70 MHz and 135 MSPS
Data rate at 16 bit1.68 Gbps at 105 MSPS
Clock3 V peak to peak differential
Thermal vias49 vias in a 7 by 7 array under the pad, per the vendor note
Temperatureminus 40 to 85 C
Processcomplementary bipolar, BiCom3
Supply sequencinginputs must stay below 0.5 V when an analog rail is off
Package sharingsame body and pin out as the 80 and 135 MSPS members

Points to check before this part goes on a BOM

The 105 MSPS rate buys 31 percent more bandwidth than the 80 MSPS member at the same 2.2 W, so the power per sample falls from 27.5 nJ to 21 nJ. On a multichannel board that is the argument for taking the faster part even when the band does not need it, because the thermal envelope is the same and the clock is the only moving item.

The headline dynamic figures in the family document are taken at 135 MSPS. A specification that quotes 95 dBc of SFDR for this order code without saying where it was measured is quoting the fastest member of the family, and the 105 MSPS column in the same table has to be read instead.

The 5 V analog rail is unusual in a converter this fast and it is what the 16 bit noise floor is bought with. A board that only has 3.3 V and 1.8 V has to add a clean 5 V rail, and the noise on that rail appears directly in the conversion because it is the reference supply as well as the input buffer supply.

The exposed pad carries 2.2 W, and the vendor note gives the via pattern as a 7 by 7 array, which is 49 vias. A board that reduces that count to save space raises the junction temperature and the first symptom is drift in the offset, not an immediate failure, so it passes first article and fails in the field.

Supply sequencing is a documented hazard rather than an inference. The document states that with one analog rail off the analog inputs must stay below 0.5 V, otherwise the protection diode between the input and that rail conducts. Any sequencer that brings the 3.3 V rail up before the 5 V rail therefore needs a clamp or an interlock on the analog input.

The 3 V peak to peak differential clock has to reach every channel at that amplitude. On a board with many channels, the fan out is the limiting element and the last channel usually shows the first loss of SNR, which reads as a per channel spread that no calibration removes.

Because all three family members share one body, the buying decision can follow the clock source. If the board is built for 105 MSPS and the clock later supports 135 MSPS, the upgrade is a part change plus a clock change, with no board spin, which is worth knowing when a long life programme is being planned.

At 105 MSPS a 16 bit word is 1.68 Gbps leaving the part, and the LVDS bus is captured source synchronously. The delay between the output clock and the data has to be tuned on the board, and a capture path carried over from an 80 MSPS build usually needs the delay re-set before the data is clean.

Where this order code fits

This order code fits multi carrier cellular receive paths where 105 MSPS covers the band of interest with some room, test and measurement digitisers, radar baseband capture and medical imaging receive channels. The same board usually serves the 80 MSPS and the 135 MSPS parts, so the rate is often chosen late, once the clock source and the thermal budget are known. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

What changes between this part and the 80 MSPS member? The rated sample rate and the power per sample. The package, the pin out, the supplies and the interface are shared.

Is a 5 V rail really required? Yes, the family runs from a 5 V analog supply plus 3.3 V analog and digital. A board with only 3.3 V cannot host it.

How much heat does one channel produce? 2.2 W at rated rate. The 70 mW power down state is how a multichannel board keeps unused channels from heating the active ones.

SUPERB quotes this order code with the date code, packing and country of origin on the offer, and the Component Lead Time Solutions page sets out what to preserve when a 16 bit channel is moved to a second source.