Contact Us

INA168NA/3K

Brand: Texas Instruments
Texas Instruments INA168NA/3K is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA168NA/3K — Power Management & Signal Chain | Superb Automation

INA168NA/3K

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA168NA/3K from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA168NA/3K: a 60 V high side current monitor in a five pin SOT-23

The INA168 measures the voltage across a shunt resistor on the high side of a load at common mode voltages from 2.7 V to 60 V and turns it into an output current. An external load resistor converts that current back into a voltage, which sets the full scale reading and, with a capacitor, the response time. The family is unipolar and meant for a supply rail monitored against ground, which covers a 48 V telecom rail, a 24 V industrial bus and a battery stack with margin left for transients. The sibling INA138 stops at 36 V, so the choice between the two is made by the rail rather than by the gain.

The vendor recommends a full scale shunt drop of 50 mV to 100 mV, which keeps the sense resistor small enough to carry the load current without dissipating watts. Bandwidth is 800 kHz with a 5 kilohm load resistor and falls to 32 kHz at 125 kilohm, so the same part can be a fast overcurrent detector or a slow average current reading depending on one component. The output is a current source, so series resistance in the trace to the measuring point does not change the reading.

Key data for the INA168NA/3K

Common mode2.7 V to 60 V on the INA168, 2.7 V to 36 V on the INA138, both in the same document
Full scaleA 50 mV to 100 mV shunt drop is the recommended range, set by the sense resistor and the load resistor
Bandwidth800 kHz with a 5 kilohm load resistor, 32 kHz with 125 kilohm, so the load sets the speed
Settling1.8 microseconds to 0.1 per cent for a 5 V step with a 5 kilohm load, 30 microseconds at 125 kilohm
NoiseOutput current noise density quoted in the electrical table, low enough for a 10 bit measurement
OutputCurrent output with 1 megohm in parallel with 5 pF, so the load resistor defines the volts per amp

Body, marking and reel data

BodyDBV, SOT-23 5 pin, 3000 pieces on a large reel, 180 mm carrier
MarkingA68 on the INA168, B38 on the INA138, which is how the two parts are told apart on a reel of unmarked bags
FinishNIPDAU, moisture level 2 with a one year floor life at 260 C
GradeAmbient minus 40 C to 125 C on the active rows, wider than the audio family in the same catalogue

Where a high side monitor replaces a low side shunt

A low side shunt is easier to measure because the common mode sits near ground, but it puts a resistor between the load and ground, which breaks a ground reference, upsets a bus, and lets a short to chassis bypass the measurement entirely. A high side shunt keeps the load ground solid and sees the fault current that a low side part would miss. The price is a common mode voltage up to the rail, which is exactly what this family is specified for.

The other practical point is that the part is a five pin SOT-23 with two pins for the sense input, one for the supply, one for ground and one for the output current. That leaves no room for a gain setting, so the full scale is fixed by the two resistors the customer chooses. Where a product needs a digital current reading rather than an analogue one, the same shunt feeds a monitor with an integrated converter, and our power management cross reference lists both routes. The cost reduction page covers how a shunt and monitor pair is chosen against a Hall sensor for the same job.

Buyer questions on the INA168NA/3K

Can it monitor a negative rail? No. The common mode range starts at 2.7 V above ground, so the part measures a positive rail against ground. A negative rail needs a different topology or a level shift.

What load resistor gives 3 V at full scale? The load resistor sets volts per amp directly, so it is chosen from the full scale current and the shunt value. Raising it increases the output and narrows the bandwidth, which is the trade the data sheet's bandwidth table describes.

Why is the marking different from the part number? The SOT-23 body carries a short code rather than the full string. A68 is the INA168 and B38 is the INA138, so a bag without a label is identified from the marking table in the data sheet.

Availability and ordering notes

The 3000 piece reel is the production packing and the same body ships in 250 piece small reels through distribution, which is what a prototype uses. Both the INA168 and the INA138 are active, so the choice is the rail voltage rather than the supply situation. We quote the reel size and the marking with the part so the goods inward check can confirm the receipt against the order, and the inspection plan for that check is set out on our incoming inspection plan page.