Contact Us

INA155E/250

Brand: Texas Instruments
Texas Instruments INA155E/250 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA155E/250 — Power Management & Signal Chain | Superb Automation

INA155E/250

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA155E/250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA155E/250: a CMOS instrumentation amplifier that works on a 3 V rail

The INA155 is a CMOS instrumentation amplifier with a rail to rail output that swings within 10 mV of either rail, built for single supply systems between 2.7 V and 5.5 V. Gain is 10 V/V with the gain pins open and 50 V/V with them shorted, and a single resistor sets any value between the two. Input bias current is 0.2 pA, which is the figure that decides whether the part can sit directly on a high impedance sensor or needs a buffer in front of it, and bandwidth is 550 kHz at a gain of 10, so a 3 V system still has usable speed for a multiplexed channel.

The E suffix in this catalogue code is the DGK body, the 8 pin VSSOP, packed 250 pieces on a small reel. That packing is what a prototype or a low volume instrument buys, and the same silicon is available in the SOIC body on a 2500 piece reel when the product moves to volume. The CMOS input stage and the rail to rail output together mean the amplifier can run from the same 3.3 V rail as the converter behind it, which removes a charge pump or a negative rail from a battery powered instrument.

Key data for the INA155E/250

Supply2.7 V to 5.5 V single supply, no negative rail needed for a bipolar signal if the reference is biased
OutputRail to rail, within 10 mV of either rail, so a 12 bit converter on 3.3 V keeps its full code range
Gain10 V/V open, 50 V/V shorted, any value between with one resistor across the gain pins
Bias0.2 pA input bias current, low enough for a pH electrode, a photodiode or a high impedance bridge
Bandwidth550 kHz at a gain of 10, which is the figure to use for a multiplexed channel settling budget
ReferenceReference pin sets the output zero, so a bidirectional sensor can sit in the middle of the rail

Body, marking and reel data

BodyDGK, VSSOP 8 pin, INA155EA/250 and INA155EA/2K5, 250 piece small reel is the published packing
SiblingsINA155U in SOIC 8 pin, tube of 75 and 2500 piece reel, both active in the current addendum
FinishLead finish is listed as call TI on several rows of this family, so the finish has to be confirmed per lot
GradeAmbient minus 40 C to 85 C, moisture level 2 with a one year floor life

Where a single supply CMOS in-amp is the right answer

A battery instrument has one rail and no room for a negative supply, and the analogue front end still has to handle a sensor whose output swings either side of its own bias point. The usual workaround is a virtual ground divider and an operational amplifier, which costs two resistors, a capacitor and a buffer, and drifts with the rail. The INA155 does the whole job in one package: the reference pin sets the zero point, the output swings to within 10 mV of the rail, and the input bias current is low enough that a 10 megohm source does not load it.

Typical uses are portable medical monitors, battery test equipment, pressure and pH sensors, and any channel that has to work from a lithium cell without a boost converter. Where the same board has to measure a low level signal next to a switching regulator, the common mode rejection and the power supply rejection decide the usable resolution, so the part is chosen with the supply noise in mind rather than only with the gain. Our amplifier cross reference lists the single supply instrumentation families by supply range and bias current, and the medical device component page covers the front ends used in patient connected equipment.

Buyer questions on the INA155E/250

Can the gain be set to 30? Yes. A resistor across the gain pins sets any gain between 10 and 50, and the data sheet gives the equation. The trimmed 10 and 50 settings keep the tightest gain error, so a calibrated range is usually one of those two.

Is the 250 piece reel enough for production? It covers a pilot build. The same silicon in the SOIC body ships 2500 pieces on a large reel, so the reel size changes with the body rather than with the electrical part.

Does it need an input filter? A CMOS input with 0.2 pA of bias current tolerates a series resistor and a capacitor without adding offset, so an RC filter at the input is the normal way to keep switching noise out of a low level channel.

Availability and ordering notes

Lead finish on this family is printed as call TI on several rows, which means the finish has to be confirmed when a customer's process document names a specific one. We confirm the finish and the reel size on the quote rather than quoting from the catalogue line alone, and where a build is short of the VSSOP body the SOIC row is the same silicon in a wider package. Parts that have gone quiet in one body are covered through the obsolete part cross reference hub.