INA111AU/1K
Product Specifications
INA111AU/1K
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA111AU/1K from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA111AU/1K: FET input instrumentation amplifier with a 50 kOhm gain term in the sixteen pin SOIC
INA111AU/1K is a high speed FET input instrumentation amplifier that sets any gain from 1 to over 1000 with one external resistor in a SOIC body of 16 pins. It uses a current feedback topology that holds 2 MHz of bandwidth at a gain of 10 and settles a gain of 100 step in 4 us to 0.01 per cent, with an input bias current under 20 pA from the FET stage, a 500 uV offset limit and 5 uV per degree of drift. The gain term is 50 kOhm, so gain is 1 plus 50 kOhm divided by RG, and the supply runs from plus or minus 6 V to plus or minus 18 V at 3.3 mA typical.
Order code and package
| INA111AU/1K | SOIC DW body, 16 pins, 1000 pieces on a large reel, Active in the addendum dated 24 July 2026, NIPDAU finish, moisture level 3 with a 168 hour floor life, marking INA111AU, minus 40 to plus 85 degrees |
| INA111AU | the same DW body in a 40 piece tube, which is the repair and prototype quantity and the row whose moisture column reads N/A because a tube is not reflowed |
| INA111AU/1K.A | the .A revision row of the same reel, printed separately with a Call TI finish column, so a material declaration has to come from the vendor rather than from the row |
| INA111AP | PDIP P body, 8 pins, 50 pieces in a tube, the through hole option for an existing socket and the only body in the family with the original eight pin arrangement |
| INA111BU/1K | the B grade in the same DW body, a separate string with its own offset window, which is the row to compare when the A grade drift is the limiting term |
Electrical parameters that decide the application
| Gain equation | 1 plus 50 kOhm divided by RG, any gain from 1 to over 1000, with the internal resistors laser trimmed as a set |
| Supply | plus or minus 6 V to plus or minus 18 V, plus or minus 15 V nominal, at 3.3 mA typical and 4.5 mA maximum supply current |
| Offset voltage | 500 uV maximum referred to the input, which is a millivolt class part rather than a precision one |
| Offset drift | 5 uV per degree maximum, and the drift row includes a term that scales with gain rather than a single fixed number |
| Input bias current | 20 pA maximum from the FET input stage, which is what allows a high impedance source without a buffer |
| Common mode rejection | 106 dB minimum at a gain of 1, rising with gain as the input stage takes over |
| Gain error | plus or minus 0.5 per cent maximum at a gain of 10 into a 10 kOhm load, with 0.1 per cent typical |
| Nonlinearity | 0.005 per cent of full scale maximum at a gain of 1, and 0.0005 per cent typical |
| Bandwidth | 2 MHz at a gain of 10 from the current feedback topology, falling to about 200 kHz at a gain of 100 |
| Settling time | 4 us to 0.01 per cent at a gain of 100, which is the figure that made the part popular in multiplexed acquisition |
| Input range | the common mode window is set by the output swing of the first stage, so it does not reach either rail and the datasheet curves show the limit per gain |
| Temperature | minus 40 to plus 85 degrees, which is narrower than the 125 degrees of the newer precision parts |
Family variants and how they differ
| Current feedback against three op amp | this part and the INA821 use a current feedback input stage that holds bandwidth at high gain, while the INA333 and the INA128 use three op amp stages whose bandwidth falls with gain, so the choice is made by the gain and the speed together |
| INA111 against INA128 | both use a 50 kOhm gain term, so a resistor set for one gives the same gain on the other, and the difference is the FET input here against the 5 nA bipolar input there |
| INA111 against INA821 | the INA821 is the modern replacement with a 35 uV offset, 0.4 uV per degree and a 125 degree ceiling, at the cost of a 49.4 kOhm gain term and a different pinout |
| A grade against B grade | the B grade carries a tighter offset window in the same body and the same reel size, so the grade is chosen by the error budget rather than by the footprint |
| Tube against reel | the 40 piece tube and the 1000 piece reel are the same silicon, but the tube row is not reflowed and therefore carries no floor life limit while the reel carries level 3 with 168 hours |
Points to check before this part goes on a BOM
The 500 uV offset is the limit that keeps this part out of precision instrumentation. A bridge with a 10 mV full scale signal sees 5 per cent of error from the offset alone, and the 5 uV per degree drift moves that by 0.05 per cent of full scale per degree. The part is a high speed acquisition amplifier, and the INA821 with its 35 uV offset is the modern part for the same socket when the signal is small.
The 20 pA input bias current is the specification that survives the years. A photodiode preamplifier, a pH electrode or an ion chamber presents a source impedance in the gigaohm range, and 20 pA through 1 GOhm is 20 mV, which is large but calculable, while the 5 nA of a bipolar input part would be 5 V and would saturate the stage. That is the reason this part is still bought for medical and analytical instruments.
The 2 MHz at a gain of 10 is the current feedback advantage: the bandwidth falls much more slowly with gain than a three op amp stage, so a gain of 100 still leaves about 200 kHz. A multiplexed acquisition system that switches channels and needs to settle inside a few microseconds is the application this topology was built for, and the 4 us settling figure at a gain of 100 is the number to check against the converter sampling time.
The 85 degree temperature ceiling is the practical limit and it applies to both grades. An industrial cabinet at 60 degrees ambient with a 20 degree rise inside the enclosure is at the limit, and a hot spot near a regulator takes it over. The newer parts at 125 degrees exist for that reason, and a replacement that ignores the ceiling will pass a bench test and fail in the field.
The supply current of 3.3 mA typical and 4.5 mA maximum is quoted as a plus or minus figure in the electrical table because the part runs on a split supply and the current flows in both directions. On a single supply arrangement the same current returns through the reference pin, so the reference source has to sink it, and a divider without a buffer will move under load.
The moisture level 3 on the reel with a 168 hour floor life is the handling fact that catches production lines. A reel opened on Monday and used on Thursday is outside the floor life unless it has been dry packed again, and the failure mode is cracking at reflow rather than an electrical fault, so it appears as a yield loss with no obvious cause. The tube row carries no such limit because a tube part is not reflowed.
Choosing RG at high gain
A gain of 10 needs 5.56 kOhm, a gain of 100 needs 505 Ohm and a gain of 1000 needs 50.05 Ohm. The 50 kOhm internal term is trimmed, so the external resistor sets the gain error and its temperature coefficient sets the drift: a 25 ppm per degree resistor adds 25 ppm per degree to a gain drift the amplifier holds to a few ppm, and the resistor becomes the limiting component above a gain of 100.
The settling time to 0.01 per cent at a gain of 100 is 4 us only when the source impedance is low and the feedback network is small. A 10 kOhm source with 50 pF of cable capacitance puts a pole at 300 kHz and the settling time triples. That is why the datasheet asks for the input filter resistors to be small and for the cable to be driven rather than passively connected.
What the FET input buys and what it costs
The FET stage removes the bias current problem and adds an offset problem: the 500 uV offset is an order of magnitude worse than the bipolar precision parts, and it drifts at 5 uV per degree. The noise is also higher at low frequencies, so an application that needs both a high source impedance and microvolt level accuracy is not served by this part and needs a chopper stabilised input instead.
Where this order code fits
Medical instrumentation, data acquisition, photodiode and ion chamber front ends and multiplexed acquisition systems are the applications the vendor names, and all of them combine a high source impedance with a need to settle quickly after a channel change. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Is the 500 uV offset good enough for a bridge sensor? Only for a bridge with a full scale above about 50 mV, since 500 uV is 1 per cent of that. Below it the offset dominates and a precision part is needed.
Can it run on a single 5 V supply? No. The minimum supply is plus or minus 6 V, so a split rail of at least 12 V is required.
What temperature range does it cover? Minus 40 to plus 85 degrees on both grades, which is narrower than the newer parts at 125 degrees.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.