Contact Us

VBTA1220NS

Brand: VBsemi
VBsemi VBTA1220NS is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBTA1220NS — Discrete & Power Semiconductors | Superb Automation

VBTA1220NS

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBTA1220NS from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBTA1220NS: a small signal N channel in an SC75 body

The VBTA1220NS is a single N channel MOSFET in an SC75 three lead body, with a 20 V drain to source rating, a plus or minus 20 V gate window, a threshold between 0.5 and 1.5 V, a drain current of 0.85 A, and an on resistance of 390 milliohm at a 2.5 V gate and 270 milliohm at 4.5 V.

This is a signal switch, not a power device. The useful way to read the page is to start from the dissipation limit rather than the current: an SC75 body can pass roughly 150 to 200 milliwatt to still air on a normal board, and at 270 milliohm that limit arrives at about 0.75 A, which is why the current rating and the thermal limit agree so closely for once.

The 0.5 to 1.5 V threshold window is wide, and it is the parameter that decides whether the part can be driven from a low voltage logic pin. The bottom of the window is essentially a depletion like behaviour and the top is a normal enhancement device, so two parts from the same reel can behave differently at a 1.8 V drive.

Key data for the VBTA1220NS

ConfigurationSingle N channel
PackageSC75, three leads, surface mount
VDS20 V
VGSPlus or minus 20 V
Vth0.5 to 1.5 V
ID0.85 A
RDS(on) at 2.5 V390 milliohm
RDS(on) at 4.5 V270 milliohm
TechnologyTrench
Gate chargeNot published, negligible at this die size
Thermal limitAbout 150 to 200 milliwatt in still air on a normal pad
Body diodeIntrinsic, anode at source

What a 0.85 A rating means in an SC75

At 0.85 A and 270 milliohm the conduction loss is 195 milliwatt, which is exactly at the thermal limit of the body. That is a well matched pair of numbers and it tells you the vendor set the current rating from the package rather than from the die. The die itself could carry more if it could get rid of the heat.

In practice that means the part runs at its rating only in still air at 25 C on a pad with some copper. At 60 C ambient the same 195 milliwatt gives a 75 C rise, and the junction sits near 135 C. Derating to 0.6 A drops the loss to 97 milliwatt and the junction to about 100 C, which is where a small signal switch should live.

For pulsed use the picture is better. A 100 microsecond pulse at 2 A is 1.08 W for a moment, and the transient thermal impedance of a small body is low enough that the junction barely moves if the duty cycle is under a few per cent. That makes the part workable as a driver for a relay coil or a small solenoid, where the current is high but the on time is short.

The wide threshold window and low voltage drive

A threshold range from 0.5 to 1.5 V is a factor of three, and it is quoted as a range because the process spreads that far. A circuit that drives the gate from 1.8 V has an overdrive between 0.3 and 1.3 V depending on the die, and the resistance at 1.8 V is not published. At 2.5 V the overdrive is between 1.0 and 2.0 V and the published figure is 390 milliohm, at the price of some parts being barely enhanced.

The engineering answer is to drive from 4.5 V where the resistance is specified at 270 milliohm and the overdrive is at least 3 V on every die. A board that has only 1.8 V available should either use a part with a tighter threshold window or accept that the current has to come down.

A wide threshold window also has a second order effect worth knowing. In a circuit where the gate is left floating or driven through a high value resistor, the leakage and the threshold decide the state, and a part that turns on at 0.5 V may conduct where a part that turns on at 1.5 V does not. A pull down resistor at the gate is mandatory, not optional.

Where the part belongs

It belongs in signal switching, small load control, level translation, LED drive at a few milliamps, and as the low side driver of a relay coil. It does not belong in a power path above a few hundred milliamps, in a circuit that needs reverse blocking, or anywhere a fault current can arrive, because there is no current limit and the die is small.

Our one stop BOM sourcing page covers how a group of passives and small switches around a controller is sourced together, which is the practical way to buy a part like this: on its own the reel cost dominates, and beside the rest of the bill it does not.

The sourcing side of this part is covered on the purchase order follow up. For a small signal part bought in low quantity, that page covers what is confirmed on an order and when it is confirmed.

Questions we get on this code

Can it switch a 500 mA relay coil? Yes, with a gate drive of 4.5 V and a flyback diode across the coil. The coil is inductive, so the drain sees the supply plus a diode drop at turn off, and the diode is what protects the 20 V rating.

Is it a drop in for the common small signal N channel parts? Often, if the pinout matches and the threshold window is acceptable. The check is the pinout, the threshold range and the resistance at the gate voltage used.

Does it have ESD protection built in? The catalogue page does not state one, so treat the gate as unprotected and add a resistor and a clamp where the gate is exposed to a connector.

What package options exist? The SC75 three lead is the body on this page. If a smaller or a leaded body is needed, ask and we check the family rather than substituting a different die silently.