Contact Us

VBQG5325

Brand: VBsemi
VBsemi VBQG5325 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG5325 — Discrete & Power Semiconductors | Superb Automation

VBQG5325

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG5325 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG5325: a 30 V complementary pair with a wider gate window

The VBQG5325 is the 30 V member of the complementary pair family, with one N channel and one P channel in a DFN body of 2 by 2 mm. Both are rated at plus or minus 30 V, the gate window is plus or minus 20 V, the thresholds are 1.6 V and minus 1.7 V, the current is plus or minus 7 A, and the on resistance is 24 milliohm for the N channel and 40 for the P at a 4.5 V gate, falling to 18 and 32 at 10 V.

Against the 20 V member of the same family the useful changes are the voltage rating and the gate window. Twenty volts of gate window instead of twelve opens the part up to a 12 V rail drive without a clamp, and a 30 V drain rating covers a 24 V supply with the usual derating rather than sitting exactly on the limit.

What did not change is the asymmetry. The P channel is still about two thirds worse than the N channel, which is the material property and not a choice, and it still decides which half of a bridge runs hotter.

Key data for the VBQG5325

ConfigurationDual, one N channel and one P channel
PackageDFN 2 by 2 mm, exposed pad, surface mount
VDSPlus or minus 30 V
VGSPlus or minus 20 V
Vth, N channel1.6 V
Vth, P channelMinus 1.7 V
IDPlus or minus 7 A
RDS(on), N channel24 milliohm at 4.5 V, 18 milliohm at 10 V
RDS(on), P channel40 milliohm at 4.5 V, 32 milliohm at 10 V
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal pathExposed pad shared by both dies

The 4.5 V column is now the working column, not the 2.5 V one

The 20 V member of this family publishes the same resistance at 2.5 V and 4.5 V, which is a promise about very low gate drive. This 30 V member does not, and that is the honest reading of a 1.6 V threshold: at 2.5 V the overdrive is under 1 V and the resistance is not specified. At 4.5 V it is 24 milliohm, and a circuit that drives from 3.3 V logic has to assume something between the two.

The practical consequence is a drive decision. A 5 V rail driving the gate through a resistor gives 24 milliohm and is the efficient choice. A 3.3 V microcontroller pin gives an unspecified resistance and should be treated as a level shifting task: a small driver or a pre driver between the pin and the gate costs one part and removes the uncertainty.

The 10 V column, 18 milliohm, is 25 per cent better than the 4.5 V column for the N channel and 20 per cent better for the P channel. That is a smaller improvement than the ratio on a higher voltage die, which suggests the silicon was optimised for logic level drive rather than for the top of its gate window.

A 30 V rating on a 24 V rail, and what the margin actually is

Thirty volts against a 24 V supply is 25 per cent of headroom on paper. In a switching circuit the switch node rings, and the ring amplitude depends on the loop inductance, the current slope and the snubber. A well laid out 24 V to 5 V converter can hold the ring to 6 or 8 V above the input, which puts the peak at 30 to 32 V and outside the rating.

That does not make the part unusable at 24 V, it makes the snubber and the loop area part of the circuit rather than optional. Short return paths, the input capacitor within a few millimetres of the pair, and a resistor capacitor snubber across the low side device are the standard answer. Without them the 30 V rating is a number that gets exceeded on the first switching edge.

A safer arrangement at 24 V is to use this pair as the gate drive stage of a larger bridge rather than as the main switch, where the currents are small and the ring is easy to control. That is a common use of a complementary pair in this size: the pair switches the gate of a big device, and the big device carries the power.

Loss split across the two channels

At 4 A in a bridge built from this pair, the N channel dissipates 384 milliwatt at 24 milliohm and the P channel 640 milliwatt at 40 milliohm. Total just over 1 W in a 2 by 2 body, which needs real copper underneath but is inside the capability of the package if the pad is at least 15 by 15 mm of two ounce copper and the ambient is not above 60 C.

The thermal question for a complementary pair is always which die is closest to the edge of the paddle. The two dies share one pad, so the cooler one heats the warmer one. A board that runs the P channel at 640 milliwatt and the N at 384 has a hot spot on one half of the pad, and the copper has to be arranged to spread from that half rather than from the centre.

Our strategic sourcing page covers how a supply is held for the life of a product, which for a complementary pair in a 2 by 2 body is worth arranging early, because the family has a small number of sources and the body size is what constrains a substitute.

The sourcing side of this part is covered on the date code management. For a pair in a small body that can sit in stores, that page covers how age is tracked and what will not go into a new build.

Questions we get on this code

Can the two channels be paralleled for more current? Not usefully. An N and a P channel in parallel do not share current evenly, and their thresholds move in opposite directions with temperature.

Is 7 A a simultaneous figure for both channels? It is one current figure for the package. Treat it as a single channel figure at 25 C case and derate for two channels conducting at once.

Does it need a gate resistor? Yes, on both gates. A 10 to 47 ohm resistor at each gate limits the driver current and damps the resonance between the gate capacitance and the trace inductance.

What is the second source situation? A 30 V complementary pair in a 2 by 2 DFN is a narrow market and the pin map is the constraint. Send the original number and we compare the pin map before quoting an alternative.