Contact Us

VBQG3322

Brand: VBsemi
VBsemi VBQG3322 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG3322 — Discrete & Power Semiconductors | Superb Automation

VBQG3322

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG3322 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG3322: two 30 V N channels in a 2 by 2 mm body

The VBQG3322 is a dual N channel MOSFET in a DFN body of 2 by 2 mm, with a 30 V drain to source rating, a plus or minus 20 V gate window, a threshold of 1.7 V, a 5.8 A current figure, 26 milliohm at a 4.5 V gate and 22 milliohm at 10 V, on trench silicon.

Two channels in 2 by 2 mm is the smallest body in this catalogue band that carries a real power die. Each channel is a separate device with its own gate, drain and source brought out, which is what makes the part useful: it can be two independent switches, a bidirectional block, or a pair that shares a rail and is driven together.

The limit is thermal and mechanical at the same time. The pad on a 2 by 2 body is small, the solder joint area is small, and the current per channel is a fraction of what the same die would carry in a 3 by 3 or an SOP8. Everything about this part is about deciding what 5.8 A really means.

Key data for the VBQG3322

ConfigurationDual N channel, independent
PackageDFN 2 by 2 mm, exposed pad, surface mount
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID5.8 A per channel
RDS(on) at 4.5 V26 milliohm
RDS(on) at 10 V22 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Isolation between channelsBoth channels share the package body, the drain connection has to be read from the data sheet
Thermal pathExposed pad, small joint area, board copper does most of the work

5.8 A per channel against 26 milliohm of channel

At 5.8 A and 26 milliohm the conduction loss in one channel is 875 milliwatt. Two channels at that current in one 2 by 2 body is 1.75 W, which is beyond what the body can pass to still air without a substantial copper plane underneath and some airflow. The number is a package and die limit, not a working current for both channels at once.

The working figure comes from the thermal resistance. A DFN 2 by 2 with an exposed pad on a 10 by 10 mm copper area sits around 90 to 110 degrees per watt junction to ambient, and with 25 by 25 mm of copper and airflow it comes down to roughly 60. A 100 C rise therefore allows 0.9 to 1.7 W in total, which at 26 milliohm is 5.9 A through one channel or 4.1 A through each of two.

Those are honest numbers for the body and they are close to the catalogue claim, which is a sign that the 5.8 A figure was set with a single channel in mind. A board that runs both channels at 3 A each, 234 milliwatt per channel, is comfortable and needs no special copper. A board that runs both at 5 A each, 650 milliwatt per channel, needs the pad area to be treated as the main thermal component.

Two independent channels, and what that costs on the board

Independence is the reason to buy this part rather than two single devices. Two channels in a 2 by 2 body save about 4 square millimetres, and on a crowded board that matters. The cost is that the copper for both pads is in one small area, so the thermal solution for two channels is harder than the thermal solution for one.

The gate drive question is the one that catches people. A 1.7 V threshold with a 20 V gate window means the part can be driven from 4.5 V logic directly, and the 4.5 V column, 26 milliohm, is only 18 per cent worse than the 10 V column. That is a well characterised logic level die, so a 5 V gate driver or a microcontroller pin through a resistor is a legitimate arrangement for a low current switch, provided the switching frequency is low enough that the gate charge does not dominate.

Above about 100 kHz the gate charge starts to matter, and since this page does not publish it, the number has to come from the data sheet before a driver is chosen. A 2 by 2 body with two dies has short internal connections and low parasitic inductance, which is an advantage for fast switching, so the part is capable of more than a slow load switch if the driver is right.

Where this part fits in a bill of material

It fits where two small switches are needed near each other and the current per channel is under about 3 A: a pair of load switches on two rails, a bidirectional block on an analog signal, a low side pair driving a small motor, or two level shifters. It does not fit where either channel has to pass a fault current, because there is no current limit inside and the safe operating area of a 2 by 2 die is limited.

Our pin to pin cross reference page covers how a candidate is checked against the original, which for a dual in a 2 by 2 body means the pin map first and the resistance second, because two vendors can use the same body size with the two channels on different pins.

The sourcing side of this part is covered on the safety stock planning. For a dual in a 2 by 2 body that is often single sourced, that page covers how a buffer is sized against the build plan.

Questions we get on this code

Are both channels rated at 5.8 A at the same time? The catalogue gives one current figure. Treat it as a single channel figure and derate for simultaneous conduction, because two channels share one thermal pad in a 2 by 2 body.

Can one channel be used as a reverse polarity block? Only in the sense of a back to back pair, because the body diode of a single N channel conducts in the reverse direction whatever the gate does.

What reel does it ship on? DFN 2 by 2 parts normally ship on 3000 or 5000 piece reels. We confirm the size on the quotation rather than stating one here.

Is it a second source for a 30 V dual in the same body? Possibly, and the check is the pin map, the threshold window and the gate charge, not the resistance. Send the original part number and we compare the three.