Contact Us

VBQF1206

Brand: VBsemi
VBsemi VBQF1206 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1206 — Discrete & Power Semiconductors | Superb Automation

VBQF1206

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1206 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1206: 20 V and 58 A in a DFN 3 by 3

The VBQF1206 is a single N channel MOSFET rated at 20 V drain to source with a plus or minus 12 V gate window and a threshold window of 0.5 to 1.5 V. It carries 58 A and its on resistance is 5.5 milliohm at a 2.5 V gate and 6 milliohm at 4.5 V, according to the catalogue table. The die is trench silicon and the body is the DFN 3 by 3.

A 20 V part with a 12 V gate window is a logic level device in the strict sense. It is meant to be driven from a 2.5 V or 3.3 V rail, not from a 10 V driver, and the 12 V window is there to protect it from the overshoot of a fast switching node rather than to be used as a drive level.

The application is a single cell battery path, a 5 V bus switch, a load switch on a portable product, or the low side of a buck that runs from a 3.3 V or 5 V rail. At 3 A and 6 milliohm the drop is 18 millivolt, which is small enough to sit in series with a battery and not notice.

Key data for the VBQF1206

ConfigurationSingle N channel
PackageDFN 3 x 3 mm with exposed pad
VDS20 V
VGSPlus or minus 12 V
Vth0.5 to 1.5 V window
ID58 A
RDS(on) at 2.5 V5.5 milliohm as published
RDS(on) at 4.5 V6 milliohm as published
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeIntrinsic, and in a battery path its direction decides the block
Thermal pathExposed pad at drain potential

Two published resistances that run the wrong way

The page prints 5.5 milliohm at a 2.5 V gate and 6 milliohm at 4.5 V, which is a resistance that rises as the gate drive increases. That is not how a MOSFET behaves in the linear region: more gate voltage gives more inversion charge and a lower resistance, all the way to the point where the gate oxide is at risk.

There are three likely explanations. The two columns may have been filled from different test conditions, one of them may be a maximum and the other a typical, or the columns may be transposed for this row. Whatever the reason, the values are close enough that the practical difference is 0.5 milliohm, and the part works either way. What matters is that a reader should not treat 2.5 V as the better drive point, and should confirm both numbers against the data sheet before a thermal budget is signed off.

The threshold window of 0.5 to 1.5 V reinforces the point. A one volt spread across a production batch means the drive level has to be chosen for the bottom of the window and the leakage checked at the top of it.

Fifty-eight amps and a 12 V gate window

At 10 A the loss is 0.6 watt and the pad on a normal island is cool. At 20 A it is 2.4 watt and the junction sits 100 degrees above ambient on a small island. At 58 A it would be 20 watt, which the body does not shed, so the headline is a die limit and the working current is 10 to 15 A.

The 12 V gate window is a real constraint in a battery product. A 12 V rail that rings can exceed it, and a part on a battery path also sees the charger voltage, which on a two cell product is 8.4 V and on a three cell product 12.6 V, already above the window. So this device is a one or two cell part, and a three cell product needs a different gate rating.

The body diode orientation decides what happens when the battery is inserted backwards and when the load dumps. In a battery path the diode is normally reverse biased in the blocking direction, and the channel is what carries the current when the switch is on.

Consolidating small switches on one board

A portable product often carries four or five different switches at 20 V and 30 V, and consolidating them to one or two codes simplifies the bill of material, the stocking and the test fixture. Our BOM consolidation page covers how that is done without losing the electrical margin any one position needs.

The consolidation has to respect the gate window, because a 12 V part cannot go into a position where the gate sees 15 V, and it has to respect the threshold window, because a position that relies on a low threshold to work from a 1.8 V rail will not accept a 2.5 V part.

The sourcing side of this part is covered on the date code management. For a low voltage switch used in volume, that page covers how age and storage are tracked through the warehouse.

Questions we get on this code

Is 2.5 V really the best gate drive? The published numbers suggest it, but a rising resistance with gate voltage is not physical. Confirm both against the data sheet before relying on either.

Can it be used on a three cell battery? No. The gate window is 12 V and a three cell pack reaches 12.6 V, which is outside it.

Is 58 A continuous? No. At 6 milliohm the continuous current in a DFN 3 by 3 is 10 to 15 A, and 58 A is a die limit at a 25 C case.

How is it packed? DFN 3 by 3 normally ships 3000 or 5000 pieces on a large reel. We confirm the reel size and the date code on the quotation.