Contact Us

VBQA2152M

Brand: VBsemi
VBsemi VBQA2152M is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2152M — Discrete & Power Semiconductors | Superb Automation

VBQA2152M

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2152M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2152M: a 150 V P channel in a DFN 5 by 6

The VBQA2152M is a single P channel MOSFET rated at minus 150 V drain to source with a plus or minus 20 V gate window and a threshold of minus 2 V. It carries minus 18 A and its on resistance is 150 milliohm at a 10 V gate. The die is trench silicon and the body is the DFN 5 by 6 millimetre package with an exposed pad.

A 150 V P channel is a high side switch on a rail that is too high for a 60 V part and too low for a 200 V one, which in practice means a 72 V battery pack, a 96 V rail or a telecom negative rail. The 150 milliohm resistance at 5 A drops 0.75 V and dissipates 3.75 watt, so the part is comfortable at 2 to 3 A and needs a thermal plane above that.

P channels at 150 V are a small cell. Most of the market solves this with an N channel and a bootstrap or a charge pump, and the P channel exists for the circuits where the gate drive has to be referenced to the source without any floating supply.

Key data for the VBQA2152M

ConfigurationSingle P channel
PackageDFN 5 x 6 mm with exposed pad
VDSMinus 150 V
VGSPlus or minus 20 V
VthMinus 2 V typical
IDMinus 18 A
RDS(on) at 10 V150 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeIntrinsic, cathode at drain
Thermal pathExposed pad at drain potential, so the copper island is a high side node
Creepage150 V between the pad and the surrounding copper is part of the assembly rating

A 2 V threshold on a 150 V part

A minus 2 V threshold on a 150 V device is low, and it is what allows the part to be turned on from a 10 V or 12 V rail referenced to the source with a level shift that only has to move a couple of volts. It is also what makes the part sensitive to a false turn on when the drain moves quickly.

The gate window is 20 V measured from the source, which on a 96 V rail means the gate can never be pulled toward ground directly. A divider, a zener and a small N channel are the standard circuit, and the resistor values are chosen so the gate source voltage stays between about 4 and 15 V over the whole rail range.

The turn off path is the part that gets neglected. When the switch has to open into a load that still has inductance, the drain rises until something clamps it, and the gate is the place where the resulting displacement current arrives. A resistor from gate to source, close to the part, keeps the gate from being lifted through the driver's impedance.

One hundred and fifty milliohm in a five by six body

At 3 A the loss is 1.35 watt and the pad on a four square centimetre island with vias puts the junction about 50 degrees above ambient. At 6 A it is 5.4 watt and the part needs a thermal plane. At 10 A it is 15 watt and the die is beyond what a 5 by 6 body sheds.

The pad is the drain, and on a high side switch the drain is the switched rail. That means the copper island moves with the load, and it is a noise source as well as a heat path. A high side switch on a 96 V rail with a large copper island is also a creepage problem, because the island sits at 96 V and the surrounding circuitry does not.

The 18 A rating is a die and bond limit at a 25 C case. The continuous figure for this body in still air is 3 to 5 A, which is the number a thermal budget should use.

Comparing a P channel against an N channel plus a driver

The honest comparison is not resistance, it is total cost. An N channel of the same voltage and current has a quarter of the resistance and needs a bootstrap capacitor, a diode and a driver referenced to the switch node. A P channel needs a resistor, a zener and a small N channel, and it dissipates three to four times as much. Below 2 A the P channel wins on simplicity and above 5 A the N channel wins on loss. Our supplier scorecard page covers how a source is scored when both routes are on the table and the decision has to survive a programme rather than a prototype.

At 150 V the P channel cell is thin, so availability usually decides. A part that is perfect electrically and single sourced is a risk on a product with a ten year life, and that risk is worth stating before the board is released.

The sourcing side of this part is covered on the incoming inspection plan. For a high voltage P channel with a thin market, that page covers what is checked before a reel enters a line.

Questions we get on this code

Can it switch a 96 V rail from a 12 V logic pin? Through a divider and a clamp, yes. Directly, no, because the gate would sit 96 V below the source.

Is 18 A continuous? No. At 150 milliohm the continuous current in this body is 3 to 5 A, and 18 A is a die limit at a 25 C case.

What about a 72 V battery pack? 150 V gives a factor of two of margin, which covers a fully charged pack and the turn off overshoot together.

How is it packed? DFN 5 by 6 normally ships 3000 or 5000 pieces on a large reel. We confirm the reel and the date code on the quotation.