Contact Us

VBPB18R47S

Brand: VBsemi
VBsemi VBPB18R47S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBPB18R47S — Discrete & Power Semiconductors | Superb Automation

VBPB18R47S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBPB18R47S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBPB18R47S: 800 V and 47 A in a TO3P

The VBPB18R47S is a single N channel MOSFET rated at 800 V drain to source with a plus or minus 30 V gate window and a threshold of 3.5 V. It carries 47 A and its on resistance is 90 milliohm at a 10 V gate. The silicon is a multi epitaxial super junction structure and the body is TO3P, the through hole package that is wider than a TO247 and uses a different mounting hole spacing.

Ninety milliohm at 800 V is a step beyond the 110 milliohm part in the same family, and it comes from a larger die in a larger tab. At 10 A it dissipates 9 watt; at 20 A it is 36 watt; at 47 A it is 199 watt, which no through hole body sheds in air and which makes the headline a die limit.

The TO3P body is the reason this part exists separately from the 110 milliohm device. The wider tab spreads the heat over a larger area and the package has a lower junction to case resistance, which matters for a converter that runs at 15 to 25 A continuously and cannot afford a fan.

Key data for the VBPB18R47S

ConfigurationSingle N channel
PackageTO3P, three lead through hole, wider tab than TO247
VDS800 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID47 A
RDS(on) at 10 V90 milliohm
TechnologyMulti epitaxial super junction
Gate chargeNot published on the catalogue page
Body diodeIntrinsic, fast recovery, and a snubber is normal in a bridge
Thermal pathWide tab to heatsink, insulated pad on an earthed sink
Package noteTO3P and TO247 do not share a hole pattern, so the body is a board and hardware decision

The 90 milliohm die and the gate charge that comes with it

A larger die has a lower resistance and a larger gate. At 800 V the gate charge of a 90 milliohm super junction part is in the tens of nanocoulombs, and at 100 kHz the charge alone costs several watts of drive power. That is why a driver for this class of part is a discrete stage rather than a microcontroller pin, and why the gate resistor is chosen from the switching waveform.

The body diode recovery also scales with the die. In a bridge the opposite switch has to clear the stored charge at every commutation, and at 800 V that produces a current spike that couples into the gate loop. A snubber across the switch, or a small saturable element, is the usual mitigation, and the value is found on a test bench rather than in a data sheet.

The threshold of 3.5 V means a 10 V drive gives 6.5 V of overdrive, which is the normal operating point. A 5 V drive would sit 1.5 V above threshold and produce a resistance well above 90 milliohm, so a 5 V gate driver on this part is a mistake that does not show up until the thermal test.

What the wider tab buys

The TO3P has a wider tab and a larger contact area than a TO247, and the junction to case resistance is correspondingly lower. At 15 A and 90 milliohm the loss is 20 watt; with a 0.5 degree per watt junction to case and a 1 degree per watt sink the junction sits 30 degrees above ambient, which is comfortable for a converter in a cabinet.

The same loss in a package with a higher junction to case resistance and a smaller contact area would run 20 degrees hotter, and that is the difference between a part that lasts and one that fails in the field after two summers. It is not a number that appears in a headline comparison.

The wider body also changes the mechanical side. The hole spacing is not the same as TO247, so a board cannot be changed between the two without a new footprint, and the heatsink hardware is different. That is worth knowing before a substitute is proposed on resistance alone.

Cost and consolidation at 800 V

At this voltage the die is the cost, and the die size is set by the resistance. A programme that needs 15 A continuous can use a 110 milliohm part and save on both the part and the sink, and a programme that needs 25 A cannot. Our how to reduce component cost page covers the order in which a bill of material is examined when the target is a lower cost per board rather than a lower price per part.

Consolidating two 800 V parts into one is possible when the lower current position can tolerate the higher resistance, and it is worth checking because two part numbers at this voltage mean two sets of qualification data and two supply risks.

The sourcing side of this part is covered on the vendor consolidation. For a family that carries more than one 800 V code, that page covers how the supply is consolidated without losing cover.

Questions we get on this code

Is 47 A continuous? No. At 90 milliohm the continuous current on a TO3P with a good sink is about 15 to 20 A, and the 47 A figure is a die limit.

Can a TO247 part be used instead? Electrically it may be close, mechanically it is not, because the hole pattern differs. That is a board change.

Is the gate charge a problem at 100 kHz? It is a real loss, and it is the reason the driver has to be sized from the data sheet rather than from a rule of thumb.

How is it packed? TO3P normally ships in tubes. We confirm the count and the date code on the quotation.