VBL1603
Product Specifications
VBL1603
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1603: 60 V and 210 A in the same TO263 footprint
The VBL1603 is a single N channel MOSFET in a TO263 body rated at 60 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 210 A of drain current, 12 milliohm at a 4.5 V gate and 3 milliohm at a 10 V gate. It has the same footprint as the higher current part in this family and a quarter of the resistance at the 4.5 V column.
The two columns differ by a factor of four, which is the widest gap in this band. That happens when a die is optimised for a 10 V drive and only partly enhanced at 4.5 V. A board budgeted on 3 milliohms and driven at 5 V gets 12, and the loss quadruples.
Sixty volts covers a 48 V system with a clamp, a 42 V rail and a 36 V pack at the top of charge with room. At the 80 per cent rule the part works to 48 V continuously, which is the right ceiling for a 48 V pack at 58 V only when a clamp holds the transients.
Key data for the VBL1603
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 60 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 210 A, a die figure at a 25 C case |
| RDS(on) at 4.5 V | 12 milliohm |
| RDS(on) at 10 V | 3 milliohm |
| Technology | Trench |
| Loss at 20 A | 1.2 W at 3 milliohm, 4.8 W at 12 milliohm |
| Loss at 80 A | 19.2 W at 3 milliohm, 76.8 W at 12 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
Four times the loss at five volts of gate drive
Twelve milliohms at 4.5 V is a real figure and it is not the same part behaviour as 3 milliohms. On a 20 A load the difference is 1.2 W against 4.8 W, which is a small heatsink. On an 80 A load it is 19.2 W against 76.8 W, which is the difference between a working board and a dead one.
That gap is the reason the gate drive has to be settled before the part is chosen. A 10 V gate from a 12 V housekeeping rail reaches the low column. A 5 V gate from a logic supply reaches the high one.
If the board has only a 5 V rail, a part with a printed 4.5 V column near its 10 V column is the better choice, and there are parts in this band that behave that way. The catalogue column is as much a specification of the gate drive as of the die.
The sixty volt ceiling on a forty eight volt pack
A 48 V lithium pack at the top of charge is about 58 V and a lead acid pack is about 58.8 V when equalising. Both are inside 60 V with almost nothing to spare. Any transient that adds 3 V at the drain passes the absolute rating.
A clamp at 55 V attached close to the switch is the working answer, with the loop from drain through the suppressor to source kept short. A clamp placed across the connector instead leaves the trace inductance between the clamp and the switch in the loop, and the drain sees the spike anyway.
Where the pack can be disconnected under load, the disconnect switch sees the full cable inductance. That is a case for the 100 V class rather than a 60 V one, whatever the steady state voltage says.
At 3 milliohm and 210 A the loss would be 132 W, and at 12 milliohm it would be 529 W. Both figures show that the current column is a die rating at a 25 C case and nothing else. The package limits the working current to a fraction of the print.
For a two ounce board with a large pad, vias into an inner plane and some airflow, a part at 3 milliohm holds around 50 to 70 A. The 12 milliohm column halves that, because the loss doubles for the same current.
The copper is the variable that matters and it is worth saying again: a pad three times the tab area with vias is not a luxury at these currents, it is the difference between the part working and the part being replaced.
Where the part fits and where it does not
It fits a motor drive on a 48 V pack, a battery disconnect, a load switch on a 48 V bus, a synchronous rectifier and an ORing element. It does not fit a 96 V pack, and it is the wrong choice where the only gate drive available is 5 V and the current is high.
For a 48 V drive the deciding parameters are the gate drive available and the clamp at the switch. Our date code management page covers how a part held between builds is tracked so the driver and the switch come from the same revision.
The sourcing side of this part is covered on the excess inventory management. For a part held between builds, that page covers how excess is identified and how age is handled.
Questions we get on this code
Why is the 4.5 V figure four times the 10 V one? Because the die needs a 10 V gate to be fully enhanced. At 4.5 V it is only partly on, and the resistance shows it.
Can it replace the 270 A part in this family? On the footprint yes. On the loss no, unless the gate drive is the same.
Is 60 V enough on a 48 V pack? At 58 V top of charge it is inside the absolute rating, and only with a clamp placed at the switch.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.