Contact Us

VBL15R30S

Brand: VBsemi
VBsemi VBL15R30S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL15R30S — Discrete & Power Semiconductors | Superb Automation

VBL15R30S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL15R30S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL15R30S: a 500 V superjunction part in TO263

The VBL15R30S is a single N channel MOSFET in a TO263 body rated at 500 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 30 A of drain current and 140 milliohm at a 10 V gate. The technology is listed as SJ_Multi-EPI, which is a multiple epitaxy superjunction process rather than a plain trench.

Superjunction is what makes 140 milliohm possible at 500 V. A plain planar die at this voltage sits nearer 400 to 800 milliohm in the same body. The charge balance columns in the drift region let the epitaxial layer be far more heavily doped for the same breakdown, which cuts the resistance per unit area by a factor of three or four.

Five hundred volts covers a rectified 220 V AC main at 310 V to 340 V with margin, a 380 V DC bus at the low end, a power factor correction stage, and the primary switch of a flyback or forward converter in an offline supply. It does not cover a 400 V DC bus with a large transient, which wants the 600 V or 650 V class.

Key data for the VBL15R30S

ConfigurationSingle N channel
PackageTO263, surface mount, tab soldered to the board
VDS500 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID30 A, a die figure at a 25 C case
RDS(on) at 10 V140 milliohm
TechnologySuperjunction, multiple epitaxy
Loss at 2 A0.56 W at 140 milliohm
Loss at 10 A14 W at 140 milliohm
Gate windowPlus or minus 30 V, wider than the low voltage parts in this band
Thermal pathTab to copper, no isolated substrate

What a superjunction die does differently

A superjunction die has alternating p and n columns in the drift region. When the device is off, the columns deplete into each other and the field is nearly uniform, which is what allows a short drift region at high voltage. When it is on, the same columns carry current in parallel, which is what gives the low resistance.

The cost is in the switching behaviour. The output capacitance is non linear and falls steeply with drain voltage, so the charge that has to be removed at turn on is concentrated near zero volts. The body diode is fast for the voltage class but it has a hard recovery, and in a bridge that recovery rings against the loop inductance.

The other cost is the safe operating area. A superjunction die has a narrow one and a ruggedness figure that is usually lower than a planar die of the same voltage. In a flyback with a clamped primary that does not matter. In a circuit that avalanche conducts on every cycle it matters a great deal.

Five hundred volts on a rectified main

A 220 V AC main rectified and smoothed sits at about 310 V, and with a 15 per cent high line tolerance it reaches 356 V. At the 80 per cent rule this part works to 400 V, which covers 356 V with 44 V left for the leakage spike from the transformer.

That spike is the number that decides the circuit. A flyback primary with 1 per cent leakage inductance produces a spike of several tens of volts on top of the reflected voltage, and a clamp network takes most of it. Without a clamp the drain passes 400 V on every cycle and the part is outside its derated ceiling.

For a 380 V DC bus the steady state is 380 V and the derated ceiling is 400 V, which is too tight for a switching node. That bus wants the 600 V or 650 V class. For a power factor correction stage running at 390 V output the same applies.

At 140 milliohm the loss at 5 A is 3.5 W and at 10 A it is 14 W. A TO263 tab on a good pad passes the first and struggles with the second without airflow. A 500 V offline converter at 100 W output draws about 1 A average from the bus, so the conduction loss in a flyback primary is small and the switching loss dominates.

That makes the gate charge and the output capacitance the numbers that matter, and neither is printed on this catalogue page. For a 65 kHz flyback the switching loss at 310 V is typically a few watts, which the tab removes. Ask for the capacitance curve before fixing the frequency.

The plus or minus 30 V gate window is wider than the low voltage parts and it suits a 15 V driver with a zener clamp. A 12 V drive is inside the window with room, and a 18 V drive is as well, but a 20 V drive with ringing is not.

Where the part fits and where it does not

It fits the primary switch of an offline flyback up to about 150 W, a forward converter on a 310 V bus, an active clamp reset circuit, a PFC stage at 380 V output at low power and a discharge switch on a high voltage capacitor bank. It does not fit a 400 V DC bus with a switching node, and it does not fit a position where avalanche energy is expected every cycle.

For an offline converter the deciding parameters are the leakage spike the clamp has to absorb and the capacitance the driver has to charge. Our one stop BOM sourcing page covers how the primary side parts are bought together so the switch, the clamp and the controller arrive as one set.

The sourcing side of this part is covered on the last time buy and LTB planning. For a primary side part in a long life product, that page covers how the last buy quantity is set before the family ends.

Questions we get on this code

Is 500 V enough for a 220 V main? Yes with a clamp. The rectified rail is 356 V at high line, and the derated ceiling is 400 V, which leaves 44 V for the spike.

Why is the resistance lower than other 500 V parts? Because the die is a superjunction, not a planar. The columns carry current in parallel and deplete into each other when off.

Is the body diode fast enough for a bridge? It is fast for the class and it recovers hard. In a bridge the recovery rings against the loop and needs a snubber.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.