Contact Us

VBL1301

Brand: VBsemi
VBsemi VBL1301 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1301 — Discrete & Power Semiconductors | Superb Automation

VBL1301

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1301 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1301: 30 V and 260 A at 1 milliohm

The VBL1301 is a single N channel MOSFET in a TO263 body, rated at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 260 A of drain current, 2 milliohm at a 4.5 V gate and 1 milliohm at a 10 V gate. It is the lowest resistance part in this band and the one with the widest gap between the two gate columns.

One milliohm changes what the loss budget looks like. At 30 A the conduction loss is 0.9 W, at 100 A it is 10 W, and at the printed 260 A it is 67.6 W. That last figure is not survivable in a TO263, so the part is a high current switch whose working current is set by the tab rather than by the die.

Thirty volts suits a 24 V rail with a clamp, a 12 V rail with a wide margin and a single 24 V battery string at the top of charge, which is 28.8 V and inside the absolute rating but above the 24 V derated ceiling.

Key data for the VBL1301

ConfigurationSingle N channel
PackageTO263, surface mount, tab soldered to the board
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID260 A, a die figure at a 25 C case
RDS(on) at 4.5 V2 milliohm
RDS(on) at 10 V1 milliohm
TechnologyTrench
Loss at 30 A0.9 W at 1 milliohm, 1.8 W at 2 milliohm
Loss at 100 A10 W at 1 milliohm
Thermal pathTab to copper, no isolated substrate

One milliohm and the copper that surrounds it

At 1 milliohm the part stops being the dominant resistance in the circuit. A 10 mm length of two ounce copper trace is about 0.5 milliohm, a solder joint is a few tens of microohms and the source bond wires inside the package are of the same order as the die. The whole loop has to be treated as the resistance, not the catalogue figure.

That changes the copper argument. A symmetric bus bar, a wide copper pour and a short current path matter more than the choice between 1 and 2 milliohm. Two boards with the same part can differ by 30 per cent in total loop resistance on copper alone.

It also changes current sharing in a parallel bank. Two 1 milliohm dies in parallel give 0.5 milliohm, and 0.2 milliohm of copper between the two sources is nearly a third of the total. Sharing at this level needs deliberate symmetry, not just two parts side by side.

The 30 V ceiling with a fast die

A 1.7 V threshold and a 30 V ceiling in the same die is a combination that turns on early and rings hard. On a 24 V rail with a fast switch, the drain overshoot from a 100 A turn off is easily 10 V, and the part has 30 V to work with. A clamp and a short loop are not optional at this current.

The low threshold also means Miller turn on is a real risk. A 0.3 V lift on the gate from a fast drain edge is enough to start conduction, and at 100 A that is a shoot through event. A hard pull down, a small gate resistor and a short gate return are the standard defences.

The gate charge of a die this large is significant, and it is not on the catalogue page. At 100 A and 100 kHz the drive power alone is several watts, which the driver has to supply and the return path has to be clean.

The threshold of 1.7 V has a third consequence in a battery product: inrush. A pack that is connected to a discharged capacitor bank pulls a current limited only by the pack resistance and the loop, and the part conducts in the linear region for as long as the driver takes to finish the transition. A soft start on the gate, or a dedicated inrush path, keeps the die inside its safe operating area during that window.

The reverse blocking behaviour matters too. A low resistance die with a large body diode passes current the wrong way when the pack is connected in reverse, and at 1 milliohm that current is limited only by the pack. A reverse polarity path ahead of the switch, or a fuse sized for the fault current, is what keeps a reversed pack from destroying the part.

Where the part fits and where it does not

It fits a battery disconnect on a 24 V pack, the low side of a power tool drive, a high current ORing switch, a load bank switch and a synchronous rectifier on a low voltage output. It does not fit a 48 V system, and it does not fit a continuous load above about 60 A for thermal reasons rather than for die reasons.

For a high current switch on a 24 V rail the deciding parameters are the loop resistance including copper and the clamp on the drain. Our vendor consolidation page covers how a part like this is kept on one source across several products.

The sourcing side of this part is covered on the safety stock planning. For a very low resistance part used on one rail, that page covers how a buffer is sized against the build plan.

Questions we get on this code

Does 1 milliohm mean no heat? No. At 100 A it is 10 W, which is a real thermal problem. It just means the die is no longer the largest resistance in the loop.

Is 260 A usable? Not in a TO263. The tab and the copper set the limit, and even 100 A needs a heavy pad and airflow.

Which gate column applies? The 10 V one for 1 milliohm. At 4.5 V the resistance doubles, which doubles the loss.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.