VBL1201N
Product Specifications
VBL1201N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1201N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1201N: 200 V and 100 A at 8 milliohm
The VBL1201N is a single N channel MOSFET in a TO263 body rated at 200 V drain to source, plus or minus 20 V on the gate, a 4 V threshold, 100 A of drain current and 8 milliohm at a 10 V gate. The technology is listed as trench, which makes the resistance figure an aggressive one for this voltage class.
Two hundred volts is the class used on 110 V and 120 V DC systems, on a boost stage fed from a 48 V rail, on a battery disconnect for a 144 V string and on the primary side of converters where a 100 V part has no margin. At the 80 per cent rule the part works to 160 V continuously.
Eight milliohms at 200 V deserves a note. A plain trench die at this voltage usually lands between 20 and 40 milliohm in a TO263, and 8 milliohm is the sort of figure a superjunction or a shielded gate process produces. The page lists trench, so the number should be confirmed on a sample before a circuit relies on it.
Key data for the VBL1201N
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 200 V |
| VGS | Plus or minus 20 V |
| Vth | 4 V typical |
| ID | 100 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 8 milliohm |
| RDS(on) at 4.5 V | Not printed on the catalogue page |
| Technology | Listed as trench, the figure is low for the class |
| Loss at 10 A | 0.8 W at 8 milliohm |
| Loss at 40 A | 12.8 W at 8 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
A four volt threshold at two hundred volts
A 4 V threshold is normal for a high voltage die and it is a benefit rather than a nuisance. It keeps the channel closed when the gate floats, it resists Miller turn on from a fast drain node, and it gives a wide margin between the off state and the noise on a gate node in a high voltage circuit.
The cost is that a 5 V logic output cannot drive it. At 5 V the gate is 1 V over threshold, the die is barely enhanced and the resistance is far above 8 milliohm. This part wants a 10 to 12 V driver, and the loss budget has to be built on that.
With a 12 V driver the gate sits 8 V over threshold, the die is fully enhanced and the published figure applies. The gate window is plus or minus 20 V, so a 12 V drive with a zener clamp leaves room for the ringing that a fast driver adds.
Confirming an aggressive resistance figure
When a published resistance is much lower than the class usually supports, the practical step is to measure it rather than argue about it. A four wire measurement across drain and source with the gate held at 10 V, at a known case temperature, gives the number the board will see. Ten parts from one lot tell you whether the figure is typical or best case.
The second measurement is the breakdown voltage. A die that reaches 8 milliohm at 200 V is working its epitaxial layer hard, and a breakdown measurement on a sample confirms the margin the circuit relies on. Both measurements take an afternoon and both are cheaper than a board revision.
The third is the body diode recovery. At 200 V the diode is slow and the reverse recovery charge is significant. In a bridge or a synchronous rectifier that charge is a loss and a source of ringing, and it is not on the catalogue page.
The gate drive has a second consequence at this voltage. A 4 V threshold with a 12 V driver gives a fast transition, and a fast transition on a 200 V node with a few hundred nanohenries of loop inductance produces a drain overshoot of tens of volts. A gate resistor large enough to slow the edge costs switching loss and saves the part, and the balance is set by the loop, not by the data sheet.
A last check is worth making on the clamp itself. Where the suppressor is placed at the connector rather than at the switch, the trace inductance between the two turns the clamp into a source of ringing and the drain sees a spike the suppressor never limits. The clamp belongs at the switch, with the return to the source pad short and direct.
Where the part fits and where it does not
It fits the switch of a boost stage from 48 V to 110 V, a battery disconnect on a 144 V string, the primary side of a converter fed from a 110 V bus, and an inverter stage on a 110 V DC system. It does not fit a rectified 220 V AC rail, and the resistance figure should be confirmed before it is used in a loss-critical position.
For a 110 V bus the deciding parameters are the transient the bus can deliver and the resistance at the gate voltage available. Our supplier quality audit page covers what is checked at the source when a published figure is more aggressive than the class usually supports.
The sourcing side of this part is covered on the incoming inspection plan. For a lot whose published figure is aggressive for its class, that page covers what is measured before it reaches the line.
Questions we get on this code
Is 8 milliohm real at 200 V? It is what the vendor publishes. It is low for a trench die at this voltage, so measure a sample before the loss budget depends on it.
Will a 5 V driver work? It will turn the part on, badly. A 4 V threshold needs a 10 V gate to reach the published resistance.
Is 100 A usable? At 80 W of loss, no. The tab and the copper set the working figure, nearer 30 to 40 A continuous with a good pad.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.