VBL1103
Product Specifications
VBL1103
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1103: 100 V and 180 A at 3 milliohm
The VBL1103 is a single N channel MOSFET in a TO263 body, rated at 100 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 180 A of drain current and 3 milliohm at a 10 V gate. The catalogue page prints one resistance column, at a 10 V gate.
Three milliohm at 100 V is a large die. At that resistance the conduction loss at 30 A is 2.7 W, at 80 A it is 19.2 W and at the printed 180 A it is 97.2 W. Those numbers show where the limit sits: this part is limited by the tab and the copper from about 50 A upwards, and the current column is a die figure at a case temperature a board does not hold.
The 3 V threshold is a compromise for a high current die. It is high enough that the channel stays closed with a floating gate and low enough that a 5 V driver turns it substantially on. The published resistance is a 10 V figure, and with a 5 V driver the real resistance is higher by an amount the page does not state.
Key data for the VBL1103
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 180 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 3 milliohm |
| RDS(on) at 4.5 V | Not printed on the catalogue page |
| Technology | Trench |
| Loss at 30 A | 2.7 W at 3 milliohm |
| Loss at 80 A | 19.2 W at 3 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
Where the tab becomes the limit
A TO263 tab is about 10 mm by 9 mm, and at 3 milliohm the loss rises with the square of the current. At 30 A it is 2.7 W and a good copper pad handles it. At 50 A it is 7.5 W and the pad needs vias into an inner plane. At 80 A it is 19.2 W, which a surface mount tab passes only with a heavy copper area and some airflow.
That curve is the reason a part like this is chosen for a pulse or for a converter rather than for a steady DC load. In a synchronous buck the switch carries a fraction of the output current for part of the cycle, so the average loss is well below the peak. In a battery disconnect the current is continuous, and the tab is the whole story.
The solder joint under the tab is part of the thermal path and part of the current path. A joint with voids raises both the resistance and the temperature, and at these currents a few percent of extra resistance is watts. Reflow profile and pad geometry matter more here than on a signal part.
Ten volts of gate drive and what happens below it
The catalogue prints a 10 V column only, so the behaviour at 5 V is unstated. With a 3 V threshold a 5 V gate has 2 V of overdrive, which is enough to conduct but not enough to reach 3 milliohm. The resistance at 5 V is likely to be half again to twice the published figure, which at 50 A is the difference between 7.5 W and 15 W.
For a converter with a 12 V housekeeping rail, drive the gate at 10 V and the column applies. For a board with only 5 V available, ask the vendor for the low gate curve before the loss budget is signed off, and be prepared to move to a part with a printed 4.5 V column.
The gate charge is not printed either. At 100 kHz and 50 A the switching loss is a real fraction of the total, and the charge curve at the working drain voltage is the number that decides it. The larger the die, the larger the charge, and 3 milliohm die is a large one.
A current column of 180 A in a TO263 is a die rating. The package has one tab and three leads, and the tab carries the drain. At 180 A the tab would have to pass that current through a solder joint about 90 square millimetres in area, and the loss at 3 milliohm would be 97 W, which no surface mount joint survives.
The working figure for a continuous load is where the loss matches what the copper can remove, and for a two ounce board with a generous pad and vias that is nearer 40 to 60 A. Above that the part needs a heatsink or a different package.
Where the load is a pulse, the die mass and the copper carry the first tens of milliseconds and the average loss decides the temperature. A 180 A pulse of a few hundred microseconds at a low duty cycle is inside the die capability. A continuous 180 A is not a surface mount question at all.
Where the part fits and where it does not
It fits the synchronous rectifier of a high current 48 V to 12 V converter, the low side of a traction drive on a 48 V pack, a battery disconnect at up to about 50 A continuous, and an ORing switch on a 48 V bus. It does not fit a 96 V pack, and it does not fit a continuous load near its printed current in a surface mount body.
For a high current switch on a 48 V rail the deciding parameters are the loss the copper can remove and the gate voltage the driver delivers. Our how to reduce component cost page covers how a part at this resistance is compared with a smaller die in parallel.
The sourcing side of this part is covered on the vendor consolidation. For a low resistance part used on several boards, that page covers which lines stay dual sourced after the consolidation.
Questions we get on this code
Can it carry 180 A? The die can at a 25 C case. The tab, the solder and the copper cannot at 97 W of loss, so the practical continuous figure is nearer 40 to 60 A.
Does it work at 5 V gate drive? It conducts, but 3 milliohm is a 10 V figure. Ask for the low gate curve before relying on it.
Is one part better than two in parallel? Above about 40 A a pair of smaller dies often spreads the heat better than one large die on one tab, and the copper between them is the engineering question.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.