VBL1102N
Product Specifications
VBL1102N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1102N: 100 V and 70 A with a 1.8 V threshold
The VBL1102N is a single N channel MOSFET in a TO263 body rated at 100 V drain to source, plus or minus 20 V on the gate, a 1.8 V threshold, 70 A of drain current and 20 milliohm at a 10 V gate. The catalogue page prints one resistance column, at a 10 V gate, and no column at 4.5 V.
The missing column is the important detail. A 1.8 V threshold suggests a die that turns on early, and a reader might assume a 5 V driver reaches the published resistance. Without a 4.5 V figure the assumption is unproven, and the part should be treated as a 10 V gate device until the vendor supplies the low gate curve.
One hundred volts covers a 48 V pack at the top of charge, a 60 V bus and a 72 V string at the low end. At the 80 per cent rule the part works to 80 V continuously, which leaves the transient room that a 60 V part does not have on the same rail.
Key data for the VBL1102N
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V typical, low for this voltage class |
| ID | 70 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 20 milliohm |
| RDS(on) at 4.5 V | Not printed on the catalogue page |
| Technology | Trench |
| Loss at 10 A | 2 W at 20 milliohm |
| Loss at 30 A | 18 W at 20 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
A low threshold at a hundred volts
A 1.8 V threshold on a 100 V die is unusual. The threshold falls as the channel is made shorter and the doping lighter, and both of those also lower the breakdown voltage, so a low threshold at 100 V means the vendor has traded some of the margin inside the die. It is a legitimate trade and it is the reason the part turns on from a 3.3 V logic output at low current.
The exposure is the off state. At 1.8 V typical the threshold band is wide, and a part at the low end conducts at 1.2 V or less of gate. On a switching node with a fast dv/dt the Miller coupling lifts the gate, and a low threshold die turns on earlier and stays on longer. A hard pull down and a small gate resistor are the standard answer.
The second exposure is the linear region. On a slow turn on a low threshold die spends longer partly enhanced, and the loss during that window can exceed the conduction loss at full current. Where the part is switched at a high frequency, the driver has to be fast enough that the transition is measured in tens of nanoseconds.
The missing low gate column
Without a 4.5 V column the honest position is that the resistance at 5 V is unknown. It is likely to be higher than 20 milliohm, because the die needs a certain gate overdrive to reach its fully enhanced state and 5 V is more than 1.8 V but less than the 10 V the column assumes.
For a circuit with a 12 V housekeeping rail there is no issue: drive the gate at 10 V through a few ohms and use 20 milliohm. For a circuit with only a 5 V rail the vendor has to supply the curve before the loss budget can be signed off. Asking for it is a two line email and it saves a board revision.
The same applies to the gate charge, which is not printed either. At 100 kHz and 20 A the switching loss is a real fraction of the total, and the curve at the working drain voltage is the number that decides it.
The body diode is part of the decision in a synchronous rectifier. Its forward drop at the dead time before the channel turns on is a loss, and its recovery when the opposite switch turns on is a ringing source. The catalogue page does not print the recovery charge or the forward drop, so on a converter that runs at 100 kHz or more the two numbers are worth asking for before the part is fixed.
Where the part fits and where it does not
It fits the low side of a motor drive on a 48 V pack, a synchronous rectifier in a 48 V to 12 V converter, a battery disconnect, and an ORing switch on a 48 V or 60 V bus at currents the tab can spread. It does not fit a 96 V pack, and it does not fit a board where the only gate drive available is 5 V and the loss budget is tight.
For a 48 V system the deciding parameters are the threshold band and the resistance at the gate voltage that is actually available. Our component lead time solutions page covers how a part like this is planned into a build rather than discovered short.
The sourcing side of this part is covered on the how to verify a drop in replacement. For a part with an unstated low gate column, that page sets out the checks made before a substitute is accepted.
Questions we get on this code
Is the 20 milliohm figure valid at 5 V? No. It is a 10 V figure. The vendor does not print a 4.5 V column, so the 5 V resistance is unknown until the curve is supplied.
Does the low threshold make it a logic level part? At low current it turns on from a logic output. At 20 A the die is far from fully enhanced at 3.3 V, so the resistance is well above the published figure.
Is it a drop in for a 4 V threshold part? On the footprint yes, on the behaviour not necessarily. A lower threshold turns on earlier on a fast node and needs a harder pull down.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.