VBK4223N
Product Specifications
VBK4223N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBK4223N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBK4223N: a dual P channel pair at 20 V in SC70-6
The VBK4223N is a dual P channel MOSFET in a SC70-6 body, each channel rated at minus 20 V drain to source with a plus or minus 12 V gate window, a minus 0.6 V threshold, minus 1.8 A of drain current, 235 milliohm at a 2.5 V gate and 155 milliohm at a 4.5 V gate. Two P channels in one six lead body is the shape used for a high side switch on two rails, a load switch pair or a signal multiplexer with a defined off state.
The gate window is the first thing to notice. Plus or minus 12 V is narrower than the 20 V of most parts in this table, so a 12 V rail applied gate to source sits exactly at the limit and a 15 V rail exceeds it. On a 12 V system the gate has to be pulled to ground through a divider or clamped, not tied directly.
The minus 0.6 V threshold means the channel is on as soon as the gate goes 0.6 V below the source. On a 3.3 V rail that is easy to arrange, and it is why the 2.5 V column exists: a 2.5 V logic output can pull the gate low enough to reach 235 milliohm.
Key data for the VBK4223N
| Configuration | Dual P channel, P plus P |
| Package | SC70-6, six lead surface mount |
| VDS | Minus 20 V per channel |
| VGS | Plus or minus 12 V, the tightest window in this band |
| Vth | Minus 0.6 V typical |
| ID | Minus 1.8 A per channel, a die figure at a 25 C case |
| RDS(on) at 2.5 V | 235 milliohm |
| RDS(on) at 4.5 V | 155 milliohm |
| Technology | Trench |
| Loss at 1 A | 0.155 W per channel at 155 milliohm |
| Loss at 1.8 A | 0.50 W per channel at 155 milliohm |
| Thermal path | Six small leads, both channels share the body |
Two channels in one body and what that costs
Two dies in one plastic body share the thermal path. Each channel can pass 1.8 A alone on a favourable case, but with both conducting at once the losses add and the body has one thermal resistance to work with. On a load switch pair driving two rails it is unusual for both to run at full current at the same time, so the sum matters only in a fault case.
The practical continuous current for each channel in this body is nearer 0.5 to 1 A. At 1 A the loss is 0.155 W per channel, which the leads can pass with a reasonable copper area. At both channels at 1 A the body holds about 0.31 W, which is already most of what a six lead package removes without airflow.
The benefit of the pair is matching. Two channels on one die share process and temperature, so a differential pair of switches or a two rail disconnect behaves the same way on both sides. That is worth more on a signal path than the thermal saving would suggest.
A twelve volt gate window on a twelve volt rail
A plus or minus 12 V gate window is comfortable on a 5 V rail and marginal on a 12 V rail. If the gate is pulled to ground to turn the P channel on, the gate to source voltage equals the rail, so a 12 V rail sits at the limit and any ringing on the rail or the gate pushes past it.
The usual answer is a divider from gate to source and gate to ground, which sets the on state at a fixed fraction of the rail, or a zener across gate and source. Either keeps the window intact as the rail moves and as the load changes. A resistor alone from gate to ground is enough on a 5 V rail and not enough on a 12 V one.
The threshold of minus 0.6 V also means the part turns on when the gate is only slightly below the source, so noise on a gate node with a high impedance pull up can turn a channel on. On a 12 V rail that is a real risk, and the pull up should be a few tens of kilohm rather than a megohm.
Where the part fits and where it does not
It fits a two rail load switch on a 5 V system, a high side disconnect on two branches of a battery product, a signal multiplexer with a defined off state and a reverse polarity element on a low voltage input. It does not fit a 12 V rail gate tied to ground, and it does not fit a load above about an amp continuous per channel.
For a two rail switch the parameters that decide the choice are the gate window, the threshold and the thermal coupling between the two channels. Our BOM consolidation page covers how a pair like this replaces two single parts on a board and what has to be checked when it does.
The sourcing side of this part is covered on the one stop BOM sourcing. For a pair of small switches on one board, that page covers how the group is bought on one order.
Questions we get on this code
Can both channels carry 1.8 A at once? The die figures say yes and the body says no. Both at 1.8 A is 1 W in a six lead package, which needs airflow and a lot of copper.
Is the 12 V gate window enough on a 12 V rail? Only with a clamp or a divider. Tying the gate to ground puts the full rail across gate and source, at the limit before any ringing.
Are the two channels independent? Electrically yes, thermally no. They share one body and one thermal resistance to the board.
What should a purchase order carry? Part number, SC70-6, and the packing the line can take. We confirm the reel quantity on the offer.