Contact Us

VBK162K

Brand: VBsemi
VBsemi VBK162K is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBK162K — Discrete & Power Semiconductors | Superb Automation

VBK162K

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBK162K from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBK162K: a 60 V small signal switch in SC70-3

The VBK162K is a single N channel MOSFET in a SC70-3 body rated at 60 V drain to source, plus or minus 20 V on the gate and a 1.7 V threshold, with 4000 milliohm at a 4.5 V gate and 2000 milliohm at a 10 V gate. Those resistances place it in the small signal class rather than in the power class, whatever the body suggests.

One figure on the catalogue page has to be read with care. The drain current column prints 0 A, which cannot be a usable rating for a part that is sold as a switch. The vendor page repeats the same zero in its parameter list, so this is not a transcription slip on our side. A part at 2 ohm cannot carry much current in any case, and a sensible working figure comes from the thermal limit rather than from that column.

Sixty volts in a three lead body is the useful part of the specification. It is the voltage class that covers a 24 V industrial rail with a clamped transient, a 36 V rail and a telecom 48 V line at the low end, in a body about two millimetres square.

Key data for the VBK162K

ConfigurationSingle N channel
PackageSC70-3, three lead surface mount
VDS60 V
VGSPlus or minus 20 V
Vth1.7 V typical
IDPrinted as 0 A on the catalogue page, treat the column as unstated
RDS(on) at 4.5 V4000 milliohm
RDS(on) at 10 V2000 milliohm
TechnologyTrench
Loss at 50 mA0.005 W at 2000 milliohm
Loss at 200 mA0.08 W at 2000 milliohm
Thermal pathThree small leads, no tab

Reading a part with an unstated current column

When the current column is not usable, the way to size the part is backwards from the loss the body can remove. A SC70-3 with three small leads removes a few tens of milliwatts comfortably and about a tenth of a watt with a generous copper area. At 2000 milliohm that puts the working current at 200 mA and below, whatever the die is capable of.

That is consistent with what a 2 ohm die is for. A part like this is chosen to stand off 60 V and to switch a small current, such as a relay coil, a divider tap on a sense network, a gate clamp or the low side of an optocoupler. It is not chosen to carry current.

If a circuit needs more than a few hundred milliamps at 60 V, the honest move is to a larger body rather than to a bigger number in the current column. The resistance falls by a factor of ten and the thermal path improves at the same time, which is what a power switch needs.

Sixty volts on a small signal node

The value of a 60 V rating in a three lead body is that it can sit on a rail where the node is not the main power path but where the voltage is present. A sense divider, a bias network, a small relay coil and a bleed path all sit at rail potential and all want a device that does not break down when the rail moves.

Spacing on a SC70-3 is fine enough that flux residue and humidity matter at 60 V. A no clean process that leaves an active residue can track across the body over a period of months. Where the part sits between two nodes at rail potential, a conformal coat or a careful cleaning step is worth more than a larger voltage margin.

The 1.7 V threshold means the part is on at a gate voltage a 3.3 V output can supply directly through a resistor. For a small signal switch driven from a logic pin that is convenient, and it saves the level shift a higher threshold part would need.

Where a part like this is used, the current is small and the voltage is high, so the parameter that decides the choice is the leakage in the off state rather than the resistance. A 60 V die in a body this small leaks nanoamps at room temperature and more at 85 C, and on a divider that holds a node for a long time the leakage sets the drift. A part with a lower threshold leaks more, so a 1.7 V part is a compromise between the drive voltage it needs and the off state it holds.

Where the part fits and where it does not

It fits a relay coil driver at tens of milliamps, a bleed or discharge switch on a 48 V capacitor, a sense network tap, an optocoupler output stage and a small signal clamp on a 24 V input. It does not fit a power switch at an amp, a load switch on a motor and any place where the loss budget is above a tenth of a watt.

For a small signal switch the parameters that decide the choice are the voltage ceiling, the threshold and the loss the body can remove. Our power management cross reference page covers how such a part is compared with an original when the original code is no longer easy to buy.

The sourcing side of this part is covered on the component lead time solutions. For a small signal part that is bought ahead of a build, that page covers how the lead time is planned rather than discovered.

Questions we get on this code

Why does the current column read 0 A? That is how the vendor page prints it, and the same zero appears in its parameter list. We treat the column as unstated and size the part from the resistance and the thermal limit instead of guessing.

What current is realistic? Around 200 mA at 2000 milliohm with a good copper area, and less on a small pad. The loss at 200 mA is 0.08 W, which is already most of what a three lead body removes in still air.

Can it switch a 48 V relay coil? Yes at coil currents in the tens of milliamps, with a flyback diode across the coil. The drain sees the coil voltage plus the diode drop, both well inside 60 V.

What should a purchase order carry? Part number, SC70-3, and the packing the line can take. We confirm the reel quantity on the offer rather than assuming it.