Contact Us

VBJ1695IS

Brand: VBsemi
VBsemi VBJ1695IS is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBJ1695IS — Discrete & Power Semiconductors | Superb Automation

VBJ1695IS

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBJ1695IS from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBJ1695IS: 60 V and 4.5 A in a SOT223 body

The VBJ1695IS is a single N channel MOSFET in a SOT223 body rated at 60 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 4.5 A of drain current, 85 milliohm at a 4.5 V gate and 76 milliohm at a 10 V gate. The body is the four lead surface mount package with a wide tab, which is a step up in thermal area from a SOT89 without a step up in footprint height.

Sixty volts in a SOT223 is a familiar combination for a 24 V industrial input, a 36 V rail and the primary side of a small converter. The part prints a 4.5 V column and a 10 V column, so it is a 5 V gate part that also improves at 10 V, and the threshold at 1.7 V means it turns on from a logic level output as well.

The current column reads 4.5 A, which in this body is a figure tied to a case temperature. The resistance is high enough that the loss at 4.5 A is 1.54 W, and the tab on a SOT223 is the only path out. Read the current column as a ceiling and the thermal path as the real limit.

Key data for the VBJ1695IS

ConfigurationSingle N channel
PackageSOT223, surface mount with a wide tab
VDS60 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID4.5 A, a die figure at a 25 C case
RDS(on) at 4.5 V85 milliohm
RDS(on) at 10 V76 milliohm
TechnologyTrench
Loss at 2 A0.30 W at 76 milliohm
Loss at 4.5 A1.54 W at 76 milliohm
Gate chargeNot printed, ask for the curve at the working drain voltage

The tab is the whole argument for this body

A SOT223 tab is roughly three times the area of a SOT23 tab and it is soldered flat to the board, so the copper under it is the heatsink. That is the reason a part with 76 milliohm is offered in this body rather than a smaller one: at 2 A it has to remove 0.3 W, which a small body manages, and at 4.5 A it has to remove 1.54 W, which only a wide tab on good copper manages.

The pad should extend past the tab and carry vias into an inner layer if the board has one. On a two layer board the copper on the reverse side does most of the work once the vias are in place. A pad the size of the tab with no vias is the usual reason a part of this kind runs hotter than the arithmetic suggests.

At 60 V the tab sits at the drain potential during conduction, so a shared metal surface needs isolation. Where the tab is soldered to a copper island that is also a switching node, the capacitance of that island to the chassis becomes part of the switching loss and part of the emissions. Small islands, short connections and a quiet return underneath are worth more than a bigger pad in that case.

Sixty volts on a 24 V industrial input

A 24 V industrial rail is specified to plus or minus 20 per cent in many standards, which is 28.8 V at the top, and it carries transients that are defined by the standard the product claims. A 60 V part at the 80 per cent rule works to 48 V, which covers 28.8 V with room for a clamped transient and does not cover an unclamped surge of the kind a long cable can deliver.

Where the input is protected by a transient suppressor at the connector, the part sees the clamp voltage rather than the surge, and a 60 V part on a 24 V rail is comfortable. Where the protection is a fuse and a capacitor, the drain node can see the full surge and the 100 V class is the safer choice.

The 1.7 V threshold makes the part usable from a 3.3 V logic output at low current, which is often what a small industrial board has available. It also means the off state depends on a solid pull down, since a gate node left floating sits near threshold on a warm board.

Where the part fits and where it does not

It fits a load switch on a 24 V input, a solenoid or valve driver at a couple of amps, a reverse polarity element, the low side of a small brushed motor and an LED switch on a 36 V string. It does not fit a 48 V pack at the top of charge, and it does not fit a continuous load near its printed current without a copper area built for it.

For a 24 V input the deciding parameters are the clamp voltage the rail actually reaches and the resistance at the gate voltage the driver delivers. Our incoming inspection plan page covers how a delivered lot is checked against those published figures before it goes to the line.

The sourcing side of this part is covered on the PCBA quote checklist. For a part that goes onto an assembled board, that page lists what a quote has to state so the offer and the build agree.

Questions we get on this code

How does it compare with a SOT23 part of the same voltage? The resistance is lower and the thermal path is much better. A SOT23 at 60 V is a signal level switch; this body is a small power switch.

Is 4.5 A a number I can use? For a pulse, yes. For continuous, work from 1.54 W and the copper area. On a two layer board with a good pad, 2 to 3 A is the usual working range.

Does it need a gate resistor? A small one, 4.7 to 22 ohm, keeps the drain ringing down and keeps the driver inside its current limit. It costs a little switching time and buys quiet.

What should a purchase order carry? Part number, SOT223, and the packing the line can take. We confirm the reel quantity on the offer.