VBI2102M
Product Specifications
VBI2102M
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBI2102M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBI2102M: a 100 V P channel in a SOT89 body
The VBI2102M is a single P channel MOSFET in a SOT89 body, rated at minus 100 V drain to source, plus or minus 20 V on the gate, a minus 2 V threshold, minus 3 A of drain current, 230 milliohm at a 4.5 V gate and 200 milliohm at a 10 V gate. P channel parts at 100 V are rare in a body this small, which is what makes the part interesting.
A P channel switch sits on the high side with its source at the rail and its gate pulled below the source to turn on. That removes the need for a charge pump or a bootstrap, which is the reason a P channel is chosen for a high side switch at low current even though its resistance per unit area is worse than an N channel of the same size.
100 V covers the negative 48 V telecom rail, which sits at minus 48 V nominal, reaches about minus 60 V at the top of the tolerance and sees transients towards minus 75 V. At the 80 per cent rule this part works to 80 V, which is inside that transient band with a clamp. It also covers a 72 V battery string and a 60 V DC bus with margin.
Key data for the VBI2102M
| Configuration | Single P channel |
| Package | SOT89, surface mount with a tab on one lead |
| VDS | Minus 100 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 2 V typical |
| ID | Minus 3 A, a die figure at a 25 C case |
| RDS(on) at 4.5 V | 230 milliohm |
| RDS(on) at 10 V | 200 milliohm |
| Technology | Trench |
| Loss at 1 A | 0.20 W at 200 milliohm |
| Loss at 3 A | 1.80 W at 200 milliohm |
| Gate drive | Gate pulled below the source, a level shift or a clamp is needed on a minus 48 V rail |
Driving a P channel high side switch
The gate has to go about 4.5 to 10 V below the source to reach the resistance columns, and on a negative rail the source sits at minus 48 V. A small signal NPN or an N channel part between the gate and the negative rail does the level shift, with a resistor from gate to source to hold the switch off when the driver is inactive.
The gate to source window is plus or minus 20 V, so a 48 V rail cannot be applied across it directly. The usual arrangement is a resistor divider or a zener between gate and source, which sets the on state at a fixed 10 V below the source whatever the rail does. That keeps the gate inside the window and keeps the resistance predictable as the rail moves.
The threshold of minus 2 V is high enough that noise on a 48 V rail does not turn the part on through the gate node, and low enough that a 4.5 V level shift is enough to enhance the die. What it does mean is that the off state depends on the gate being held at the source, so the pull up resistor is a functional part and not a nicety.
Two hundred milliohm at 3 A in a SOT89
At 200 milliohm and 3 A the conduction loss is 1.8 W, which is more than a SOT89 removes in still air on a pad the size of the tab. At 1 A the loss is 0.2 W and the body is comfortable. The honest continuous current for this part on a normal board is nearer 1 to 1.5 A than 3 A, and the number rises with copper area and airflow.
At 100 V the die is large for the current it carries, which is why the resistance is 200 milliohm. The area goes into voltage withstand rather than into conductance. That is the trade at this voltage and it is the reason a P channel at 100 V is a low current switch by nature rather than a power switch.
The tab is the drain, which on a P channel is the negative node. On a negative rail the tab sits at the rail potential, so a shared heatsink or a metal chassis needs isolation. Where the part is used as a reverse polarity or an inrush element on a telecom line, that is a safety item rather than a thermal one.
Where the part fits and where it does not
It fits a high side disconnect on a minus 48 V line at an amp or two, an inrush limiter on a 72 V string, a reverse polarity element on a 60 V input and a small hot swap on a telecom card. It does not fit a load above about 1.5 A continuous without a large copper area, and it does not fit a position where the gate cannot be held below the source.
For a telecom line the questions that decide the part are the transient the line can deliver and the gate clamp that keeps the switch inside its window. Our power management cross reference page covers how the candidate is compared with an original on those parameters.
The sourcing side of this part is covered on the supplier onboarding checklist. For a part bought from a new source, that page covers what has to be documented before the first shipment.
Questions we get on this code
Can it be driven straight from a microcontroller pin? Not on a 48 V rail. The pin sits near ground and the source sits at minus 48 V, so the gate needs a level shift and a clamp before it can be pulled below the source.
Is 3 A usable? At 1.8 W of loss in a SOT89, no, not continuous. Work back from the loss the pad can remove and expect a figure around a third to a half of the printed one.
Does 100 V cover a minus 48 V line? It covers the steady state and a clamped transient. An unclamped spike towards minus 100 V leaves no margin, so a transient suppressor belongs on the line.
What should a purchase order carry? Part number, SOT89, and the packing the line can take. We confirm the reel quantity on the offer.