VBGM1201N
Product Specifications
VBGM1201N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGM1201N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGM1201N: 200 V and 100 A in a TO220 body
The VBGM1201N is a single N channel MOSFET in a TO220 body, rated at 200 V drain to source, plus or minus 20 V on the gate, a 4 V threshold, 100 A of drain current and 10 milliohm at a 10 V gate. The silicon is a shielded gate trench and the package is the through hole body that has been in power supplies for decades.
200 V is the class used on 110 V DC systems, on the output of a rectified 110 V AC rail after a step down, and on the primary of a converter fed from a 96 V or 110 V battery. It is also the class used where an 80 V part is not enough margin but the frequency is too high for a 600 V superjunction part to be efficient, which is the middle ground this part occupies.
A TO220 is a through hole body with a metal tab and a single mounting hole. It is chosen for two reasons: the tab can be screwed to a heatsink, and the leads can take the thermal cycling of a high power board without a solder joint under the die. Both matter at 100 A, where a surface mount tab would be the limit long before the die.
Key data for the VBGM1201N
| Configuration | Single N channel |
| Package | TO220, through hole, tab to a heatsink or to copper |
| VDS | 200 V |
| VGS | Plus or minus 20 V |
| Vth | 4 V typical |
| ID | 100 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 10 milliohm |
| Technology | Shielded gate trench |
| Body diode | Intrinsic, cathode at the drain |
| Tab | Drain, electrically live, needs an insulator against a shared heatsink |
| Isolation | None in the body, a pad is a separate item |
| Gate charge | Not printed, ask for the curve at 160 V drain |
The 4 V threshold and what it costs
A 4 V threshold is high for a modern die and it is deliberate. A high threshold keeps the channel closed when the gate is floating, which matters in a circuit that comes up before the driver has a defined state, and it keeps the die from turning on through the Miller capacitance when the drain swings. The cost is that a 5 V logic output cannot drive it: at 5 V the gate is barely above threshold and the die is far from its 10 milliohm state.
With a 10 V driver the part behaves as the table says. With a 12 V driver the resistance improves a little more and the gate charge goes up. With a 15 V driver the gate is inside the plus or minus 20 V window but with less room for the ringing that a fast driver adds on the gate node, so a 12 V rail with a zener clamp is the usual compromise.
The gate charge at 160 V of drain is the number that decides the switching loss, and the catalogue page does not print it. For a converter running at 100 kHz with a 40 A load, the difference between a 30 nC and a 60 nC gate charge is a few watts, which is the difference between a small heatsink and a large one. Ask for the curve before the frequency is fixed.
Mounting a through hole part at 100 A
A TO220 at 100 A has three leads and a tab, and the current has to arrive and leave through them. The drain is the tab, so the tab is live and a shared heatsink needs an insulating pad and a shoulder washer. That pad adds thermal resistance, usually 0.5 to 1.5 C per watt, which at 10 W of loss is 5 to 15 C of extra junction temperature. It is part of the calculation, not a detail to add at the end.
The source lead carries the full current and it also carries the sense connection. A source connection taken from the lead has the lead resistance in series with the sense, and at 100 A a 1 milliohm lead is 100 mV of error. Where the current is measured, take the sense from the die side of the lead or add a separate sense pin.
The lead length also sets the parasitic inductance in the source path, and that inductance works against the gate drive: the di/dt in the source raises the source potential during turn on and takes drive away from the gate. A short lead and a tight gate loop are worth more at 100 A than a faster driver.
Where the part fits and where it does not
It fits a 110 V DC bus switch, the low side of a motor drive on a 96 V pack, the primary switch of a converter fed from a 110 V rail, a battery disconnect on a 110 V string, and any place where a through hole body with a screw down tab is easier to cool than a surface mount pad. It does not fit a rectified 220 V main, a 200 V DC bus without derating, or a high frequency converter where the gate charge matters more than the package.
For a 200 V switch on a converter that is short of parts, the pair of questions is whether the candidate's threshold and gate charge match the original and whether the tab can take the same heatsink. Our BOM shortage recovery page covers how a shortage is closed on a line without changing the switching behaviour of the board.
The sourcing side of this part is covered on the BOM consolidation. For a through hole part that appears on several boards, that page covers how the same code is pooled across builds.
Questions we get on this code
Can it be driven from a 5 V microcontroller pin? Not usefully. The threshold is 4 V and the resistance is quoted at 10 V. A 5 V gate leaves the die in a resistive state that will heat. Use a gate driver with a 10 to 12 V rail.
Does the tab need an insulator? It does when the heatsink is shared or grounded. The tab is the drain, so an uninsulated mounting puts the drain at the heatsink potential, which is a shock and a short circuit risk.
How much current at 100 kHz? The conduction loss at 30 A is 9 W and the switching loss at 100 kHz with a 60 nC gate is a few more. A 30 A continuous figure on a proper heatsink is realistic; 100 A is a die rating.
What should a purchase order carry? Part number, TO220, and whether the tab is expected to be isolated at the board level. We confirm the packing on the offer.