Contact Us

VBGL1103

Brand: VBsemi
VBsemi VBGL1103 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGL1103 — Discrete & Power Semiconductors | Superb Automation

VBGL1103

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGL1103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGL1103: a 100 V, 120 A shielded gate part in TO263

The VBGL1103 is a single N channel MOSFET in TO263, the body also called D2PAK, rated at 100 V, plus or minus 20 V on the gate, 120 A of drain current, with a threshold of 3 V and 3.7 milliohm at a 10 V gate, on shielded gate trench silicon.

TO263 is the surface mount version of TO220: a large tab that lies flat on the board and a body that stands above it. That tab is the reason this part exists, because 3.7 milliohm at 100 V dissipates real power and a DPAK cannot pass it.

One hundred volts covers a 72 V battery, a 80 V DC bus and the primary side of a 48 V converter with a wide margin. At 120 A the die is large, and in this body the copper under the tab is the whole thermal story.

Key data for the VBGL1103

ConfigurationSingle N channel
PackageTO263, D2PAK, surface mount with a large tab
VDS100 V
VGSPlus or minus 20 V
Vth3 V
ID120 A
RDS(on) at 10 V3.7 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, recovery moderate at this voltage
Thermal pathLarge tab to a copper pad, the best path in the family
Gate chargeLarge die, a dedicated driver is required
Typical use72 V battery, 100 V bus, high current motor drive
IsolationNone, the tab is the drain

Why the body changes the current rating

The TO263 tab is roughly three times the area of a DPAK tab, and its junction to ambient resistance on a copper pad is about half. At 3.7 milliohm and 50 A the loss is 9.3 W, which a D2PAK on a heavy copper pad can just about pass with a 150 C rise, and which a DPAK cannot.

That is why the same die is offered in different bodies with different current ratings that look inconsistent until the thermal path is considered. The electrical ratings are the die, the current rating is the case temperature, and the case temperature is the board.

At 25 A the loss is 2.3 W and the rise is around 50 C on a good pad, which leaves plenty of margin. At 40 A it is 5.9 W and 130 C, which is the practical ceiling without forced air.

One hundred volts and 3.7 milliohm

A 100 V shielded gate die with 3.7 milliohm is close to the limit of what the technology gives at that voltage. The figure of merit, resistance times gate charge, is what improved with the shield, and it is the parameter that decides whether the part can be used at 100 kHz or only at 20 kHz.

The threshold of 3 V means a 10 V drive, and the gate charge of a die this size needs a driver with a few amps of peak current to keep the switching loss inside the die rather than in the driver's linear region.

The body diode conducts during the dead time in a synchronous rectifier, and at 50 A its drop is about 0.9 V, which is 45 W for the duration of the dead time. That is why the dead time is short and why a parallel Schottky is sometimes used despite the extra part.

The dead time question is where this part is usually finalised. In a synchronous buck the low side channel has to be off before the high side turns on, and the body diode conducts during that gap. At 50 A the diode drop of 0.9 V gives 45 W during the gap, so a 50 ns dead time at 100 kHz is 0.25 per cent of the period and about 11 mW on average. A 300 ns dead time is six times that and starts to matter in the efficiency budget. The driver's dead time setting, not the part, sets this loss, which is why a 3.7 milliohm device and a 300 ns dead time can be worse than a 5 milliohm device and a 50 ns dead time.

Body diode recovery then adds to it in a hard switched bridge, where the diode is forced to block while charge is still stored. That recovery current flows through the opposite switch and shows up as a spike on the drain waveform. A snubber reduces the spike and adds loss; a shorter dead time reduces the stored charge and is the better fix when the driver allows it.

Where the part fits and where it does not

It fits a 72 V battery disconnect, a 100 V bus load switch, a high current motor drive at 25 to 40 A, and the low side of a 96 V to 48 V converter. It does not fit a hot swap without a safe operating area check, and it does not fit a rail that rings above 100 V without a clamp.

Our supplier scorecard page covers how a source is scored across a programme, which matters for a part whose performance depends as much on the copper as on the die.

The sourcing side of this part is covered on the supplier corrective action. For a part whose behaviour depends on the copper, that page covers how a field return is closed out at the source.

Questions we get on this code

Can it replace a TO220 part? Electrically close, mechanically different. The D2PAK needs a pad on the board and cannot take a clip on the tab from above in the same way.

How much copper does the tab need? As much as the board allows, with vias into an inner plane. Below about two square centimetres the current rating collapses.

Is 100 V enough for a 72 V battery? A 72 V lithium pack charges to 84 V, and a switching spike adds more. One hundred volts leaves 16 V, which is workable with a clamp and tight for a motor.

What should a purchase order carry? Part number, TO263 body, reel size and date code. We confirm the reel size on the quotation.