Contact Us

VBGE1805

Brand: VBsemi
VBsemi VBGE1805 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGE1805 — Discrete & Power Semiconductors | Superb Automation

VBGE1805

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGE1805 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGE1805: an 80 V, 120 A shielded gate part at 4.6 milliohm

The VBGE1805 is a single N channel MOSFET in TO252 rated at 80 V, plus or minus 20 V on the gate, 120 A of drain current, with a threshold of 3 V and 4.6 milliohm at a 10 V gate, on shielded gate trench silicon.

Four point six milliohms at 80 V is a very large die for a DPAK, and 120 A is the number that goes with it. The pair has to be read together with the thermal path, because a tab that carries 120 A of bond wire has a limit of its own.

This is the class used in a 48 V to 12 V converter at a few hundred watts, in a 60 V battery disconnect, and in a motor drive where the current is high and the switching frequency is moderate.

Key data for the VBGE1805

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS80 V
VGSPlus or minus 20 V
Vth3 V
ID120 A
RDS(on) at 10 V4.6 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, forward drop around 0.8 V at rated current
Thermal pathDrain tab, the die is large and the tab is the limit
Gate chargeHigher than a smaller die, needs a real driver
Typical use48 V synchronous buck, battery disconnect, motor drive
IsolationNone, the tab is the drain

One hundred and twenty amps in a DPAK

The current has to leave the die through bond wires and the tab. A DPAK typically has two or three source bond wires, and each is good for a few amps continuously. The 120 A figure describes a pulse that the die can pass, not a current the wires can carry for long.

At 4.6 milliohm and 30 A the loss is 4.1 W, and a DPAK on a copper plane with 35 degrees per watt gives a 145 C rise. At 20 A the loss is 1.8 W and the rise 64 C, which works. So the working current is 15 to 25 A on a board and up to 40 A with a proper heatsink.

This gap between the label and the board is normal for every part in this class. The number that should be used for a thermal calculation is the resistance at the working junction temperature, which for a 4.6 milliohm die at 125 C is nearer 6.5 milliohm.

Eighty volts and 48 V systems

A 48 V lead acid string at 58 V on equalise and a 60 V lithium pack at full charge both sit comfortably under 80 V, with 20 V of margin. That margin covers the turn off spike of a motor and the surge of a load step.

It does not cover a 60 V telecom bus with a lightning surge, where the transient can exceed 100 V, and it does not cover a 72 V battery. In those cases a 100 V or 150 V part is used and the resistance rises.

The 20 V gate window is standard. On a 48 V rail the gate is driven from a 10 V supply, not from the rail, so the window is not a constraint unless the drive is transformer isolated and rings.

The copper under a D2PAK style tab is not just a heatsink, it is part of the current path. At 20 A the source current leaves through the leads and the drain current enters through the tab, and any narrowing in that copper adds resistance in series with the 4.6 milliohm channel. A pad that is one millimetre wide at the neck has more resistance than the die, and the measurement on the bench then disagrees with the data sheet. The practical rule is that the copper carrying the drain should be at least as wide as the tab for its whole length, with vias into an inner plane at the far end rather than under the tab.

That same copper decides the thermal resistance. A tab soldered to two square centimetres of two ounce copper with a dozen vias into a ground plane sits near 25 degrees per watt. The same tab on a narrow track with no vias sits above 60, and the current rating falls accordingly.

Current sensing in a 48 V rail is often done across the switch itself rather than a shunt, because a 4.6 milliohm channel gives a usable signal and saves a part. The catch is that the resistance changes with temperature by about 0.3 per cent per degree, so a reading taken cold is 20 per cent low at 100 C. A sense circuit with a temperature compensation term, or a calibration at the working temperature, is needed before the reading is used for protection rather than for indication.

Where the part fits and where it does not

It fits a 48 V synchronous buck at 200 to 500 W, a 60 V battery disconnect, a 48 V motor drive at 20 to 30 A, and a load switch where the on resistance has to be very low. It does not fit a 72 V battery, and it does not fit a hot swap without a safe operating area check.

Our NPI production launch checklist page covers what is verified before a high current board goes into production, which is where a 4.6 milliohm part and its copper are signed off.

The sourcing side of this part is covered on the incoming inspection plan. For a high current part, that page covers what is measured when the reel arrives rather than after the board fails.

Questions we get on this code

Can it carry 120 A continuously? No. The bond wires and the tab limit the continuous current to a fraction of that. Use 15 to 25 A on a board as the starting point.

Is a 10 V gate drive required? The resistance is specified at 10 V. At 4.5 V it works but the resistance is higher and the threshold of 3 V leaves little overdrive.

Does it need a snubber? At 48 V with a fast edge, ringing is common. A small RC snubber across the switch or a ferrite in the drain path is the usual fix, and the board routing should be checked first.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm availability on the quotation.