Contact Us

VBGE1606

Brand: VBsemi
VBsemi VBGE1606 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGE1606 — Discrete & Power Semiconductors | Superb Automation

VBGE1606

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGE1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGE1606: a 60 V, 90 A shielded gate part in TO252

The VBGE1606 is a single N channel MOSFET in TO252 rated at 60 V, plus or minus 20 V on the gate, 90 A of drain current, with a threshold of 2.5 V and 6.4 milliohm on resistance. The catalogue names the technology as SGT, shielded gate trench.

A shielded gate sits a second, grounded electrode under the gate in the trench. It screens the gate from the drain, which cuts the gate to drain capacitance by an order of magnitude and lets the die be optimised for resistance without paying for it in switching speed.

The result at 60 V and 6.4 milliohm is a part that can switch at a few hundred kilohertz without a large driver, which is the reason this technology took over from plain trench in the 40 to 100 V range.

Key data for the VBGE1606

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS60 V
VGSPlus or minus 20 V
Vth2.5 V
ID90 A
RDS(on)6.4 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, recovery better than plain trench at this voltage
Thermal pathDrain tab to copper or heatsink
Gate chargeLow gate to drain charge is the point of the structure
Typical use48 V DC-DC, synchronous rectifier, motor drive
IsolationNone, the tab is the drain

What the shield does to the switching behaviour

The gate to drain capacitance is the path by which a fast drain voltage change couples into the gate. In a plain trench part that capacitance is large and the Miller plateau is long, so the switching time is set by how hard the driver can push charge through it.

With a shield in between, that coupling falls, so the same driver gives a faster edge, and the part can switch at a higher frequency with the same loss. It also makes the turn off less sensitive to the gate resistor, which helps with dV/dt induced turn on in a bridge.

The shield does not remove the output capacitance, which is still there and still has to be charged at every turn on. At 60 V and this die size the energy per cycle is modest, so the frequency limit is the driver and the board routing rather than the part.

Ninety amps and 6.4 milliohm

At 6.4 milliohm and 30 A the loss is 5.8 W, which in a DPAK on a copper plane is a 230 C rise, so 30 A is not continuous. At 15 A it is 1.4 W and a 56 C rise, which works. At 20 A it is 2.6 W and 100 C, which is the edge.

So the working current is 15 to 20 A on a board with a decent plane, and higher with a heatsink. The 90 A figure is a case at 25 C, and at 60 V the die is small enough that the package limits the current long before the silicon does.

The body diode conducts in a synchronous rectifier for the dead time, and at 20 A its 0.8 V drop dissipates 16 W during that interval. That is why the dead time is kept short and why the diode's forward characteristic matters as much as the channel resistance in a synchronous buck.

The shield changes one more thing that is easy to miss: the gate charge curve. A shielded gate part has a flat Miller plateau and then a sharp rise, so the driver has to supply a defined charge in a short time rather than a charge spread over a long plateau. That makes the switching loss predictable, and it also makes the driver's peak current rating the parameter that sets the edge speed. A driver rated at 0.3 A will switch this die in a few hundred nanoseconds at 48 V, which is slow enough to lose real energy at 200 kHz. A driver rated at 2 A will do it in tens of nanoseconds and the loss moves from the die to the driver, where it belongs.

Paralleling two of these for a 100 A rail is common and works if the gates are driven separately. A shared gate resistor lets the faster die take the current during the edge and the slower one take it afterwards, and the resulting current hogging shows up as one part running 20 C hotter than the other. Two resistors of the same value, placed at the gate of each part rather than at the driver, keep the edges closer and the sharing within a few per cent.

Where the part fits and where it does not

It fits a 48 V to 12 V synchronous buck, a 48 V motor drive at 10 to 20 A, a battery disconnect, and a load switch on a 48 V rail. It does not fit a 60 V rail with a hot plug surge, and it does not fit a bridge without checking the diode recovery at the switching frequency.

Our PCBA quote checklist page covers what has to be settled before a 48 V board is quoted, from the copper weight under the tab to the gate drive available.

The sourcing side of this part is covered on the PCBA test coverage strategy. For a 48 V board, that page covers what is tested on the line and what is left to the engineering bench.

Questions we get on this code

Is 6.4 milliohm at 10 V? Yes, that is the specified gate voltage. At 4.5 V the resistance is higher and the catalogue does not print it.

Is 60 V enough for a 48 V battery? A 48 V lead acid string reaches 58 V on equalise, which leaves 2 V. Add any switching spike and the rating is gone. A 75 V or 80 V part is safer.

Does the shield make it immune to dV/dt turn on? No, it reduces the coupling. The gate resistor and the source inductance still decide whether a bridge cross conducts.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm the reel size on the quotation.