Contact Us

VBE5415

Brand: VBsemi
VBsemi VBE5415 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE5415 — Discrete & Power Semiconductors | Superb Automation

VBE5415

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE5415 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE5415: an N and a P channel with a common drain in TO252-4L

The VBE5415 puts one N channel and one P channel in a TO252-4L body with the two drains joined inside the package. Each die is rated at 40 V, plus or minus 20 V on the gate, 50 A of drain current, with thresholds of 1.8 V on the N side and -1.7 V on the P side. The catalogue gives 14 milliohm and 16 milliohm in its two columns, the first pair for one die and the second for the other.

Four leads rather than three is the mechanical signature: source of the N channel, source of the P channel, the common drain on the tab, and a gate pin for each. It is a half bridge in one package with the midpoint already made.

That saves the board area of two packages and, more importantly, it removes the stray inductance between the two drains. In a switching cell that inductance is what turns a clean edge into a ringing one, so putting the connection inside the package is an electrical decision as much as a mechanical one.

Key data for the VBE5415

ConfigurationN channel and P channel, common drain
PackageTO252-4L, four leads plus tab
VDSPlus or minus 40 V
VGSPlus or minus 20 V
Vth1.8 V on the N side, -1.7 V on the P side
IDPlus or minus 50 A
RDS(on)14 milliohm and 16 milliohm across the two catalogue columns
TechnologyTrench
Body diodesTwo, both intrinsic, both able to conduct
Thermal pathThe tab is the common drain and carries both dies
Gate chargeNot published, two dies to drive
Typical useHalf bridge, motor drive, bidirectional switch
Isolation between diesNone, they share the drain

What a common drain pair is for

A half bridge needs the low side source at ground and the high side source at the switch node, which means two devices with a common drain at the switch node. Putting both in one package with the connection made on the lead frame removes a bond wire and a length of track from the highest dV/dt node in the circuit.

The same pair also makes a bidirectional switch. With one channel on and the other off, the path conducts in one direction and blocks in the other, and swapping the gates reverses it. That is useful for a battery to bus connection where current has to flow both ways but be interrupted.

The limitation is that the two dies are not matched. One is N and one is P, so their thresholds, resistances and capacitances differ, and a circuit that treats them as symmetric will have a different dead time requirement on each side.

Thermal coupling in a shared tab

Both dies sit on the same tab, so the tab temperature is set by the total dissipation and each junction adds its own rise on top. In a half bridge the low side usually dissipates more, because it carries the full current for longer and switches at a lower voltage, and its heat raises the high side junction as well.

At 14 milliohm and 10 A each side dissipates 1.4 W, so the tab carries 2.8 W into the board. With 30 degrees per watt at the tab that is an 84 C rise, and each junction adds 10 to 20 C more. That puts the working current around 10 A per side for a board cooled by copper, not the 50 A on the label.

For a motor drive running at 20 kHz the switching loss adds to that, and the pair is a 5 to 10 A bridge. For a static bidirectional switch the current can be higher, because the switching loss happens once.

Matching is the other thing to check. A common drain pair with an N channel at 14 milliohm and a P channel at 16 milliohm has a different resistance in each direction, so a bidirectional switch built from it is not symmetric. Current flowing one way sees the N channel, the other way the P channel, and the voltage drop differs by about 15 per cent. In a battery to bus connection that asymmetry is harmless. In a circuit that measures current from the drop across the switch, it is a calibration error that has to be trimmed out.

Where the pair fits and where it does not

It fits a 24 V motor half bridge, a battery to bus bidirectional switch, a 12 V or 24 V load disconnect with a common midpoint, and any place where two devices have to be close together. It does not fit a 40 V rail that rings, and it does not fit a circuit that needs matched dies, because the two channels are different types.

Our BOM consolidation page covers how two separate packages are replaced by one integrated part, which is exactly what this pair does to a half bridge line.

The sourcing side of this part is covered on the vendor consolidation. For a half bridge that used two packages, that page covers which lines stay dual sourced after the consolidation.

Questions we get on this code

Can the two channels be used independently? Yes, as long as the common drain connection suits both uses. They cannot be separated.

Which resistance belongs to which die? The catalogue prints two columns and does not label them per die. The N channel is normally the lower of the two. We confirm the pair from the data sheet before quoting.

How are the gates driven? The N side needs a gate above its source, the P side a gate below its source. In a half bridge that means a bootstrap or a driver for the N side and a level shift or a driver for the P side.

What should a purchase order carry? Part number, TO252-4L body, reel size and date code. We confirm the reel size on the quotation.