Contact Us

VBE17R10S

Brand: VBsemi
VBsemi VBE17R10S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE17R10S — Discrete & Power Semiconductors | Superb Automation

VBE17R10S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE17R10S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE17R10S: a 700 V, 10 A N channel in TO252

The VBE17R10S is a single N channel MOSFET in TO252 rated at 700 V, plus or minus 30 V on the gate, 10 A of drain current, with a threshold of 3.5 V and 600 milliohm at a 10 V gate, on superjunction multi epitaxial silicon.

Seven hundred volts is chosen when 650 V is not enough margin. A 277 V RMS mains exists in some markets, a three phase 400 V system rectifies to 565 V, and a flyback on a 480 V supply can see over 600 V at turn off. Each of those pushes the switch above the 650 V class.

Six hundred milliohm at 10 A is 60 W, so the working current is 2 to 3 A in a board and the rating is a pulse. What the part is really for is holding off a high voltage while carrying a small current.

Key data for the VBE17R10S

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS700 V
VGSPlus or minus 30 V
Vth3.5 V
ID10 A
RDS(on) at 10 V600 milliohm
TechnologySuperjunction, multi epitaxial
Body diodeIntrinsic, hard recovery
Thermal pathDrain tab to copper or heatsink
Gate chargeNot published on the catalogue page
Typical useThree phase rectified bus, 480 V supply, high voltage start up
IsolationNone, the tab is the drain

When 650 V is not enough

A three phase 400 V supply rectifies to 565 V DC and can reach 600 V during a regeneration event. A flyback on that bus with a 150 V reflected voltage and a 100 V leakage spike sees 850 V, which no 700 V part survives, so the topology changes to a two switch forward or a bridge rather than the part changing to 900 V.

A 480 V supply rectifies to 680 V, which leaves 20 V on a 700 V device and no room for a spike. In that case the part is used on a lower rail derived from the bus, or the topology clamps the switch to the bus with a diode.

The practical use of a 700 V part is on a 400 to 480 V bus with a clamped topology, or on a 600 V bus where the switch never sees the full bus plus a spike. The voltage rating is a ceiling, not a working point, and the clamp is part of the circuit.

Six hundred milliohm and the switching loss

At 600 milliohm and 2 A the conduction loss is 2.4 W, which a DPAK on a copper plane can pass with about 100 C of rise. At 3 A it is 5.4 W, which needs a heatsink. At 1 A it is 0.6 W, which is comfortable anywhere.

The switching loss at 700 V is dominated by the output capacitance and the gate charge, both of which rise with die area. A 600 milliohm die at 700 V is not small, so at 100 kHz the switching loss can exceed the conduction loss at 1 A and the part runs hotter at light load than at heavy load, which is a sign that the frequency is too high for the die.

The honest operating point for this part in a DPAK is 1 to 2 A at 50 to 100 kHz with a copper plane, or 3 A with a heatsink. Anything above that belongs in a larger body.

There is a mechanical point that matters as much as the electrical one at 700 V. The tab of a DPAK is the drain, and at 700 V it sits at a potential that will arc to anything close. A heatsink bolted to the tab has to be isolated with a pad rated for the voltage, and the creepage distance from the tab to the nearest low voltage track has to be checked against the pollution degree of the enclosure. Most failures of high voltage parts in the field are not die failures at all; they are tracking across the board surface from the drain pad to a neighbouring node after a season of dust and humidity.

The resistance of a high voltage part is hard to measure in circuit because the meter current is tiny compared with the leakage that the surrounding components inject. A four wire measurement across the tab and the source, with the gate held at 10 V from a separate supply, gives the true figure. A two wire measurement through the board tracks adds their resistance, and on a 600 milliohm part that error can be tens of milliohms, which is enough to make two good parts look different.

Where the part fits and where it does not

It fits a 400 V bus start up circuit, a 480 V auxiliary supply under 20 W, a high voltage level shift, and a 600 V bus switch with a clamp. It does not fit a 480 V bus switch without a clamp, and it does not fit any bridge or synchronous rectifier because of the body diode.

Our BOM scrubbing page covers how a high voltage line is checked against the topology it actually sits in, which is where a 650 V part in a 700 V position gets caught before a build.

The sourcing side of this part is covered on the one stop BOM sourcing. For a high voltage line with several small parts around it, that page covers how the group is bought on one order.

Questions we get on this code

Is 700 V enough for a three phase 400 V input? The rectified bus is 565 V, and a clamped switch can sit on it. Without a clamp, no.

Why is the resistance so high? A 700 V superjunction die has to hold a thicker depletion region than a 500 V part, and the resistance follows the voltage squared for a given area.

Can it be paralleled for more current? Yes, but the resistance is high enough that two in parallel only reach 300 milliohm, and the gate charge doubles. A larger single die is usually better.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm availability on the quotation.