VBE1405
Product Specifications
VBE1405
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1405: a 40 V, 85 A N channel for 24 V systems
The VBE1405 is a single N channel MOSFET in TO252, rated at 40 V, plus or minus 20 V on the gate, 85 A of drain current, with a threshold of 2.5 V. The catalogue gives 6 milliohm at 4.5 V and 5 milliohm at 10 V, on trench silicon.
Forty volts is the standard class for a 24 V system with some margin, and for a 12 V system with a lot of margin. The threshold of 2.5 V means the part is specified at 4.5 V and 10 V rather than at logic level, which is a different drive requirement from the 20 V parts in the same family.
The resistance is low for the voltage class. Five milliohm at 40 V is the kind of figure that used to need a much larger package, and it comes from cell density rather than from a special technology.
Key data for the VBE1405
| Configuration | Single N channel |
| Package | TO252, DPAK, exposed drain tab |
| VDS | 40 V |
| VGS | Plus or minus 20 V |
| Vth | 2.5 V |
| ID | 85 A |
| RDS(on) at 4.5 V | 6 milliohm |
| RDS(on) at 10 V | 5 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, recovery matters in a bridge |
| Thermal path | Drain tab to copper or heatsink |
| Gate charge | Not on the catalogue page |
| Typical use | 24 V motor drive, battery switch, DC-DC low side |
Forty volts on a 24 V rail
A 24 V lead acid battery sits at 27.6 V on float charge and can be pulled to 32 V during equalisation, and a 24 V lithium pack can reach 29.4 V. Forty volts leaves 8 to 12 V of margin, which covers cable inductance and the turn off spike from a modest load.
It does not cover a load dump or a long inductive cable without a clamp. The catalogue page gives no avalanche energy, so a rail that can spike above 40 V needs a transient suppressor or a higher voltage part rather than a hope.
In a 12 V automotive system 40 V is thin. A load dump on a 12 V bus can reach 40 V or more for hundreds of milliseconds, and a part with no avalanche rating is not the right choice there. A 60 V part is the minimum for a 12 V automotive rail.
Eighty five amps and five milliohm
At 5 milliohm and 30 A the loss is 4.5 W, which on a 40 degrees per watt tab is a 180 C rise, so 30 A is not continuous. At 15 A it is 1.1 W and a 45 C rise, which works. At 20 A it is 2 W and an 80 C rise, which is the edge.
The 85 A rating assumes a case at 25 C and a die at its maximum, which needs a heatsink that holds the tab cold. In a real board the copper is the heatsink and the working current is 15 to 20 A.
At 5 milliohm the die is large and the gate charge is high. A 10 V driver with a 2 A peak output is appropriate. A logic pin will turn the part on eventually and will dissipate a lot of energy doing it.
One thermal number that is easy to forget in a 24 V motor drive is the freewheel loss. When the low side switch turns off, the motor current keeps flowing through the body diode of the opposite device or through a separate diode, and at 10 A the drop is around 0.8 V, which is 8 W for the fraction of the period that the diode conducts. In a chopper running at 20 kHz with a 50 per cent duty, the diode may conduct for a microsecond at each edge, which is 2 per cent of the time and 160 mW on average. In a locked rotor condition the current is higher and the diode conducts longer, and that is the case that sets the thermal sizing of the whole bridge rather than the nominal running point.
If a 24 V drive needs more than 20 A, two of these in parallel reach 2.5 milliohm and halve the conduction loss, which is cheaper than moving to a larger body. The catch is current sharing. Two dies with thresholds 300 mV apart share a load unevenly, and the hotter one takes more current and gets hotter still. A separate gate resistor on each, and a source connection taken to a common point rather than daisy chained, keeps the sharing within about 20 per cent.
Where the part fits and where it does not
It fits a 24 V motor drive, a 24 V battery disconnect, the low side of a 24 V to 12 V synchronous buck, and a 12 V load switch with generous margin. It does not fit a 12 V automotive rail without a load dump clamp, and it does not fit a rail above 40 V at all.
Our supplier quality audit page covers what is checked at a source before a 40 V power part is used in a build, from the wafer lot to the final test data.
The sourcing side of this part is covered on the supplier onboarding checklist. For a 40 V power part in a 24 V system, that page covers what a new source has to document before its first shipment.
Questions we get on this code
Is it logic level? Not in the usual sense. The 2.5 V threshold allows a 4.5 V drive to reach 6 milliohm, but a 3.3 V pin gives only 0.8 V of overdrive at the top of the threshold window, which is not enough.
Can it be used on a 12 V automotive rail? Only with a transient clamp. The part has no published avalanche rating and a load dump exceeds 40 V.
How does it compare with the 20 V part in the same body? Same package, same 5 to 6 milliohm class, twice the voltage. The 40 V die is larger for the same resistance, so it has more gate charge.
What should a purchase order carry? Part number, TO252, reel size and date code. We confirm availability when the quantity is known.