VBE1206
Product Specifications
VBE1206
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1206 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1206: a 20 V, 100 A N channel in TO252
The VBE1206 is a single N channel MOSFET in TO252, rated at 20 V drain to source, plus or minus 20 V on the gate, 100 A of drain current, with a threshold window of 0.5 to 1.5 V. The catalogue gives 6 milliohm at a 2.5 V gate and 5 milliohm at 4.5 V, on trench silicon.
One hundred amps in a DPAK is the most quoted and least usable number on the page. The die can carry it for a moment, the wire bonds and the tab cannot carry it continuously, and the resistance figure is what actually sets the working current.
The threshold window is wide, from 0.5 to 1.5 V, which is typical for a logic level part at this voltage. It is also the parameter that decides whether the part behaves the same way in two different builds.
Key data for the VBE1206
| Configuration | Single N channel |
| Package | TO252, DPAK, exposed drain tab |
| VDS | 20 V |
| VGS | Plus or minus 20 V |
| Vth | 0.5 to 1.5 V |
| ID | 100 A |
| RDS(on) at 2.5 V | 6 milliohm |
| RDS(on) at 4.5 V | 5 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, low forward drop at this resistance class |
| Thermal path | Drain tab, the whole of the heat leaves through it |
| Gate charge | Not on the catalogue page, significant at this die size |
| Typical use | 12 V load switch, battery protection, motor drive |
What 5 milliohm buys and what it costs
At 5 milliohm and 20 A the loss is 2 W. At 40 A it is 8 W. A DPAK with a good copper plane sits near 40 degrees per watt, so 2 W is an 80 C rise and 8 W is not survivable. The working current is therefore 15 to 25 A on a board and higher only with a heatsink.
The cost of a 5 milliohm die is gate charge. A die with this many cells in parallel has a gate capacitance in the tens of nanofarads, and driving it at 200 kHz takes real current. A microcontroller pin through a 22 ohm resistor will spend microseconds in the linear region, and during that time the die is dissipating the full load current at a resistance that is far above 5 milliohm.
That is why a part like this belongs with a gate driver, not with a direct logic connection, even though its threshold allows a logic connection. The threshold says it will turn on, not that it will turn on fast enough to keep the switching loss out of the die.
The threshold window of 0.5 to 1.5 V
A one volt window across production is normal for a logic level trench part and it has two consequences. The first is that the on resistance at a 2.5 V gate differs from part to part, because the overdrive differs by up to a volt. The second is that the turn off point differs, so a circuit that relies on the gate being pulled to 1 V to guarantee off is not guaranteed at the bottom of the window.
For a load switch this hardly matters. For a synchronous rectifier or a bridge it matters a great deal, because a low threshold part turns off later and the cross conduction window widens. A gate resistor to ground and a driver with a solid pull down are the two practical answers.
The temperature coefficient of the threshold is negative, about -3 to -5 millivolts per degree. At 125 C the top of the window is nearer 0.9 V, and at minus 40 C it is nearer 1.7 V. A 3.3 V drive still works at both ends, a 1.8 V drive does not.
The inrush case deserves its own number. A load switch closing into a bank of capacitors draws a current limited only by the loop resistance, and at 5 milliohm that can be a hundred amps for tens of microseconds. The die survives a pulse like that if the energy is inside the safe operating area, and the safe operating area for a 20 V part is generous because the voltage across the die collapses to almost nothing during the pulse. The problem is not the die but the rest of the loop: the connector, the track and the capacitor have to take the same current, and a soft start circuit that ramps the gate over a millisecond turns a hundred amp spike into a five amp ramp. That ramp is the reason load switch controllers exist, and a bare gate resistor is not a substitute.
Where the part fits and where it does not
It fits a 12 V battery disconnect, a motor drive in the 10 to 20 A class, a reverse polarity switch on a portable product, and a synchronous buck low side on a 12 V input. It does not fit a 20 V rail that rings, because the rating is the rail and there is no avalanche margin published.
Our power management cross reference page covers how a 20 V logic level part is compared with another on the parameters that decide behaviour, and the threshold window and gate charge are the first two on the list.
The sourcing side of this part is covered on the how to reduce component cost. For a 20 V switch that appears several times on one board, that page covers where a lower cost equivalent can be used and where it cannot.
Questions we get on this code
Can it switch 100 A? No. The figure is a die limit at a case temperature no board reaches. Plan for 15 to 25 A continuous with good copper, and check the pulse rating separately for inrush.
Will a 3.3 V pin turn it on? Yes. It will not turn it on quickly. Use a driver when the part is switching rather than sitting on.
Is 20 V enough for a 12 V rail? With a clean rail, yes. A 12 V rail with a load dump or a long cable can exceed 20 V, and this part has no avalanche rating published, so clamp the rail.
What should a purchase order carry? Part number, TO252, reel size and date code. We confirm the reel size on the quotation.