VBE1158N
Product Specifications
VBE1158N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1158N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1158N: the 150 V, 25 A, 74 milliohm member of the family
The VBE1158N is a single N channel MOSFET in TO252, rated at 150 V, plus or minus 20 V on the gate, 25.4 A of drain current, with a threshold of 2.5 V and 74 milliohm on resistance, on trench silicon.
It sits in the same voltage class as the 15 A, 100 milliohm part and differs in three ways that matter together: the die is larger, the resistance is lower, and the threshold is higher. That combination is not a coincidence. A larger die with more cells in parallel reaches a lower resistance and needs more gate charge, and a higher threshold is the price of a thicker body region under the gate.
Twenty five amps and 74 milliohm in a DPAK is again a case temperature rating. The die can carry it, the tab cannot without help.
Key data for the VBE1158N
| Configuration | Single N channel |
| Package | TO252, DPAK, exposed drain tab |
| VDS | 150 V |
| VGS | Plus or minus 20 V |
| Vth | 2.5 V |
| ID | 25.4 A |
| RDS(on) | 74 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, recovery charge not on the catalogue page |
| Thermal path | Drain tab to copper or heatsink |
| Gate charge | Higher than the smaller die in the same family, ask for the curve |
| Typical use | Battery disconnect, DC bus switch, motor drive |
| Isolation | None, the tab is the drain |
Choosing between the two 150 V members
The 15 A and the 25 A parts are not interchangeable in a circuit, they are a choice. The lower resistance part halves the conduction loss at the same current, but its higher threshold means it needs more gate drive before it reaches that resistance, and its larger die means more gate charge, which becomes switching loss at high frequency.
For a load switch that stays on for seconds at a time, the lower resistance part wins because the switching loss happens once. For a converter running at 100 kHz or more, the larger gate charge can cost more than the conduction saving, and the smaller die may run cooler overall.
The threshold also decides what drives it. Two point five volts is fine with a 10 V gate driver and marginal with a 4.5 V one, because the overdrive at the top of the threshold window is only about 2 V. A part with a 1.89 V threshold has more room at 4.5 V but turns on earlier when the gate node is noisy.
Twenty five amps and the tab
At 74 milliohm and 25 A the loss is 46 W, which is not a DPAK figure. At 5 A it is 1.85 W, which with 45 degrees per watt is an 83 C rise and workable. At 8 A it is 4.7 W and the rise is 210 C, which is not.
So the working current is again 4 to 7 A on a board, more with a heatsink. The 25.4 A rating belongs to a case held at 25 C, and it is printed on every catalogue page in this class because it is measured the same way for every part.
What changes between parts is where the resistance curve sits at temperature. A trench die of this class typically has a resistance temperature coefficient of 0.35 per cent per degree, so 74 milliohm at 25 C becomes about 100 milliohm at 125 C. That is the number to use for a thermal calculation, not the 25 C value.
The two 150 V parts also differ in how they are packed and priced, and that difference is usually larger than the electrical difference. A die of this size ships on a 2500 piece reel, and a build that needs 300 pieces carries the rest as stock. That stock then sits on a shelf and its date code ages, which is a cost nobody puts in the BOM. When a part is used at 5 A rather than 20 A, the smaller die is the cheaper and more sensible choice, and the 25 A rating is paid for in area that the circuit never uses. Matching the die to the load is the single easiest saving on a power line, and it starts by reading the resistance at the working current rather than the current on the label.
Where the part fits and where it does not
It fits a 96 V battery disconnect that closes once per mission, a DC bus precharge bypass, a motor drive in the 5 to 8 A class, and a synchronous rectifier on a 48 V output where the diode recovery is not critical. It does not fit a hard switched bridge at high frequency without checking the gate charge and the diode recovery.
Our component lead time solutions page covers what is done when a 150 V part is quoted long and a second source has to be qualified without changing the board.
The sourcing side of this part is covered on the BOM shortage recovery. For a 150 V line that is short while a build is waiting, that page covers how a shortage is closed without changing the switch.
Questions we get on this code
Is the 74 milliohm figure at 10 V? Yes, that is the gate voltage for the resistance column on this part. At 4.5 V the resistance is higher and the catalogue does not print it, so ask for the curve if the gate drive is below 10 V.
Can the 15 A and 25 A parts share a board position? Electrically they are close, mechanically identical. The difference is gate charge and threshold, so a driver sized for one may not suit the other.
What is the gate charge? Not published on the catalogue page. For a die of this size expect tens of nanocoulombs, and confirm from the data sheet before fixing the driver.
What should a purchase order carry? Part number, TO252, reel size and date code window. We confirm availability on the quotation.